MSE22DRAWH General Electric Refrigerator - Instructions

I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and applied a little lubricant to the cam and job complete.

I simply removed the screws holding the plastic face plate to the old auger/ice bucket and attached it to the new one. It was a simple procedure

Turned off water to ref , removed bottom kick plate , got a towel and disconnected the water line plastic fitting and un screwed the (2) tube clamps un screwed the coupling and ((carefully )) slid out the tube from the compression ferrels ! ( Be careful and do not break or distort them + remember exactly the order they are removed ! Slid the protector spring shroud from the plastic tube , took ogg the top hinge cover then remover the top hinge . Carefully lifted the door off feering the plastic tube through the bottom hinge with my foot ! Got the door off removed the bottom hinge + put the new on on, then removed the door cam which was broken on the bottom of the door , lifted the door up and carefully fed the water line through the new bottom hinge . Attached the top hinge and reassembled the rest same as I had dissambled it . Turned on water ( checked for leaks ) ! All working 100% a-ok ! This company is the best ! Ordered the part at 1 pm and had the part at 2 pm the following day many thanks : )

First we removed the door. Then we had to hammer the old part off including the old rivot. We fould a screw that fit and put this piece on. We held the door in place and screwed the hinge on the main unit.

First I took everything out of the fresh food door, then I removed the top hinge cover using a philips head screwdriver, and a nutdriver for the two screws holding the upper hinge. Lifted the door off the bottom pin, and placed it on the floor. Then took off the bottom hinge and used the Dremel tool to grind off the rivet holding the broken door cam on the bottom hinge. Used a nut and bolt to hold the new cam in place, and put the lower hinge back on. Then replaced the other cam on the bottom of the door itself, using the nutdriver. (Be sure to buy two cams, and have the bolt and nut to replace the rivet). Reinstalled the bottom hinge, put the door on, replaced the top hinge, and presto! Works great! Thanks to the others on this site for their stories - really helped make it an easy and quick repair!

Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door now self closes .

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Opened the box, removed the ice maker, removed the old ice maker from freezer, empty drawer of ice into the sink( the hardest part of the job) Phillips screw driver and removed the four screws holding the plastic front on and installed it on the new ice maker. Put it in freezer and I am back in business . This is real easy

replaced lights in refrigirator and freezer

Let me start by saying, I usually hire something like this out but figured I would give it a try. The install was fairly straight forward, however it would’ve been nice if the instructions would have been more useful. Instructing me to remove one screw to release the auger and solenoid enclosure wouldve been nice. There were 3 other screws that I didn’t need to remove and they were the ones holding the auger in place, which made assembling that much more difficult. Once to enclosure was removed, and the solenoid was exposed, it was a seemless process. I would however, recommend paying attention to or taking a picture of the connections on the solenoid. I was lucky to remember or got lucky. Regardless, I was able to complete the project successfully. If I had to do it again, I believe it can be done in 30 minutes or less.

First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.

Ordered at PartSelect and received the auger and blade within days. Printed the parts diagram and proceeded to take the auger apart the time it took would have been much less but I seized the opportunity to do a deep cleaning of the old parts before replacing them....The part diagram was the key to simplicity and the fast shipping was awesome. Thanks I'll be back....

This one is a no brainer… One Phillips screw on top to pull top door hinge trim. Two nuts and the top hinge is free. Then pull the door… it helps if you unload all the crap in the door bins. Remove the remnants of the door cam and that leaves a pop rivet. Put some vise grips on the head and use a hacksaw to remove the lower part of the rivet. Then pop-rivet the new door cam in place. If you don’t own a pop-rivet tool, I guess you could use a 10/32” screw and nylock. Plop the door back on and you’re done. Took all of about 15 minutes.

The old cam had broken and was on the floor. I ordered one new cam. I should have been told to order at least two, I did not know they worked in pairs. So I had to re-order, I ordersed four, I was able to see that the other (freezer door has cracked cams) door will soon need replacement of the cams. I had trouble installing the new part because the rivit also needed to ba replaced. I did a "Rube Goldgerg" to get the new part to sit properly. I drilled the hole open a little and forced the part into place. All is well. Thank you very much!

1. Put all perishable food into ice chest. Empty door shelves.
2. Remove top hinge cover with Philips screwdriver.
3. Supporting door, remove top hinge attached by two hex screws.
4. Lift door off bottom hinge.
5. On bottom of door, unscrew the hex screw holding the broken plastic cam.
6. Loosen the second hex screw enough to free the broken cam.
7. Replace the cam and tighten the hex screws making sure the opening of the cam lines up with the hole under the door.
8. Snap off plastic grill at the bottom of the refrigerator.
9. Remove bottom of the two hex screws holding the bottom hinge tot eh refrigerator body.
10. Loosen the second screw enought to rotate the hinge upsidedown. Tighten the screw again.
11. Now the rivet bottom is exposed so as to facilitate drilling it out to remove the broken cam.
12. Loosen the hex screw again and turn it back rightside up. Reinstall the bottom screw and tighten both of them.
13. Using an appropriate size bolt, lockwasher and nut, install other new cam.
14. Reinstall door reversing steps 1 to 4.
15. Don't forget to return the food to the 'fridge, by the way!