TFX22JABBAA General Electric Refrigerator - Instructions

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Removed top hinge assembly to pull door away from bottom hinge (2x hex bolts) Discovered that the pin on the bottom assembly had broken off. Removed and replaced bottom hinge assembly (2x hex bolts). Aligned door with top and bottom hinge pins. Tightened all hex bolts. Done

I followed the many post on replacing this part and everything went well. I had a little trouble getting the hinge post into the new hinge assembly, but with a slight adjustment it fell into place. I checked to see what tools I would need to do the job and had them ready before I even started. I removed the door and had it back on in maybe 10 minutes and I am not exactly Mr. Fix It. The only advice I can add to what everyone else has said is you should look the job over a little before you take the door off and have your tools ready. Then you won't have the door off for too long. I'd like to thank this site and everyone who gave advice on how to fix this problem. It made the whole job very easy.

blocked up refrigerator door.removed old hinge, and put new one on,with socket set.

This is a side-by-side unit. After blocking up the closed refrigerator door to the correct height to match the freezer door, I removed the lower hinge pin assembly by taking out two bolts. Save the shims (my had two) for the new hinge pin. Then remove the cam riser from the bottom of the door by taking out two bolts. Install the new cam riser on the bottom on the door. Then install the new hinge pin assembly. Total time 15 minutes.

shimed the door up to its proper level. removed plastic cam from bottom of door with a socket disconnected the water line fitting and clamp. with a nut driver removed the hinge assy from cabinet being careful i sled the hinge assy off the plastic water line being sure not to kink the line, sled the new hinge assy back on the water line and mounted the new hinge assy to the cabinet and connected the water line back up and turned on the water and checked for leaks, all went well. place the bottom grill cover back on.

Followed directions in your video. Very helpful. Be certain to pay strict attention to how old part is removed. Had a little trouble replacing door on lower pin/hinge. Helps to have a little assistance. Good suggestion from another customer: get the kit.

I replaced both bottom hinges on my GE refrigerator. The hint that they were worn out was that both the freezer door and fresh food door would not close completely. You had to lift the door on the hinge to get it to close. Many of the GE service repair people recommend complete removal of each door to replace the bottom hinge. I found I could use a couple of wood blocks tall enough to take the weight of the door, jacking it up off of the hinge so could loosen the hex head screws. The freezer door hinge took a few minutes longer because the water supply line for the icemaker which is routed through the tube in the hinge. Overall, an easy repair and the cost of two repair visits was saved.

Replaced the gasket and the hinge assembly. Replaced the hinge assembly on the freezer door as well since it was worn. YOU DO NOT NEED A DREMEL to cut anything. People doing that are trying to save $10 but don't do it. Just order the hinge assembly. It comes with the loose cam riser and the second cam riser that is attached to the hinge. DON'T CUT ANYTHING. Super easy. I prepped the door for the hinge replacement the night before. Removed fridge magnets, etc. Moved everything from inside the door to the shelves. Got home from work (package was there in two days, fast) and it took 5 minutes for the Fresh Food Door hinge replacement. Removed hinge cover, removed 4 hex screws (two on top and two on bottom). Swapped hinge and cam. Be sure to use the cam that came with the hinge. Always replace in pairs. Freezer was more tricky. Turned off water. Had to remove a clip (small phillips head screw) on the white tubing. Unscrewed plastic nut. Pulled off spring from tubing. Set spring, nut, and clip with screw aside. Removed hinge cover, unplugged electronics, removed 4 hex screws (two on top and two on bottom). Swapped hinge and cam. Super easy.

Noticed hinge cam riser broken in 3 pieces. Took fridg door off, 3 screws on top. 2 screws on bottom loosend one screw and removed other screw. replaced cam riser and reassembled. Wife helped.

Watched PartSelect video and did exactly as video said. Had finished product in less than 30 minutes.6 bolts and one screw.

Removed top hinge, lifted door from bottom post. Removed post with nut driver/socket, removed corresponding bracket/receiver from door. Attached new parts to refrigerator base and bottom edge of door. Was careful to replace part pieces in the same order as original, and secured tightly. Lifted door onto bottom hinge post, leveled the door and replaced top hinge.

There were some great posts on similar repairs that made me realize that it was best to get the whole hinge assembly. The video regarding the repair was completely accurate down to the size of the socket wrench required.

As suggested by your web site. Thanks. BC

Followed the video to replace bottom hinge assembly. The only hiccup was that the video instruction was for the fridge side door, so there wasn't step by step instruction for dealing with the electrical connection at the top of door or the water line at the bottom. However, it was simple enough to figure out. Replacement took about 20-25 mins.