GTS22ISSARSS General Electric Refrigerator - Instructions

pull out the slide pan lh and replace for the part

It was very tricky getting the old piece out, even though it was partially broken... I ended up snapping the old piece to remove it. Trying to install the new track with the glass shelf above was not working at all, but once I removed the glass shelf above it, the new piece went in pretty easily. With the glass shelf out, I could angle the track upward to get it into position. In retrospect, I should have removed the glass shelf from the start... it would have made removal of the old piece much easier.

Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.

Took out shelf, unscrewed old track, screwed on new track. Only thing is not a standard flat or Phillips screw head so if you don't have a star head bit, you are out of luck.

First I unplugged the refrigerator. I removed the cardboard from the back and unhooked the inlet water line with a wrench and the water line to the ice maker, which was a quick connect. I unplugged the wire harness and removed the valve, then installed the new valve, plugged in the wire harness and hooked up the water lines. I turned on the water line and plugged in the refrigerator. The ice maker works great.

I took the pan out, replaced the bar with the new part - slide pan RH - and I was back in business. It couldn't have been easier.

I unscrewed two brackets on each side (Had to buy the correct little screw driver) and screwed in the new ones.Easy!

Remove entire shelf from refrigerator and removed broke, set the replacement part in place, screwed it in and it worked perfectly, done infive minutes. Took me longer to take out the self that to do the replacement.

Went to Sears, where I bought the Fridge, they could not locate the part I needed, so I went on line, and found partselect.com, entered the proper information, found the part I needed fast, ordered the part, received it in two days time, I already had the old part off, so it took less than ten minutes to replace it with the new part, works great, the people at partselect.com were great, an if needed, I will gladly order from them again.

My snack tray guide rail cracked and this was the easiest repair I've ever made.

After removing all the parts, the bins and a large glass fitted shelf or lid, on top of the two crisper bins I then removed the whole frame the three glides are mounted to. The frame is molded into one large piece matching the whole horizontal space of the refrigerator, so it is wiggled loose from its space. I lifted out the whole thing and placed it on a surface on which I could work while see everything I was doing. With no screw (both top and bottom of the U-shaped gripper “clevis” end are solid) or other type fastener that could be removed I finally just pried the "clevis" of the center glide that grips the front of the frame. This clevis grips a set of small plastic studs that fit into matching round indentations in the top and bottom of the clevis jaws. It’s necessary to keep the stud from slipping back into the first indentation while opening up the other side of the jaw so that both are free at the same time and the clevis will slide sideways. Using a butter knife because it was a good fit and stiff enough, I released the top, and then the bottom using the knife to bend it a little bit. The clevis opens up just enough to allow the edge of the frame it’s gripping to be released from its grip. The new one is put back in exactly the same manner but in reverse. The opposite end from the clevis simply tilts up until it can be disengage and reengaged in the same manner

condenser fan on bottom condenser not runningchanged fan and fan motor

I removed the ice marker first and took the back panel off using a nut driver. Be careful I had wires tied to the back panel, so I moved it like opening a door, right to left. The I removed the fan motor. Be careful not to damage the fan blades. I took the fan blades off and the dust cover. The dust cover was very tight. I had to use a very small screw driver to get it off. When I put the dust cover on the new motor I did not push it down tight. I turned the spindle of the new motor to make sure it turned. The put everything back. Turned it on and it worked. I put the ice marker on last. Take a note of how far the fan blades are on the spindle. The refrigerator now turns off more often.

I removed the ice maker, and removed the upper plastic covers, that just snap in and out of their locations, you can then see the evaporator fan blades. then I removed 2 hex screws, located in the top corners, holding a metal cover in place,lifting up from the bottom of the cover and slowly pulling it out of the freezer compartment. I can now see the screws holding the evaporator fan motor in place. Unplug the connector wiring to the motor and unclip the ground wire from the frame, It is easier to replace the fan blade,lid bumpers, dust cap,grommets, and fan motor this way. while you have everything in easy access, I took time to clean everything and replaced the foam strips, assure tight fit causing excellent air flow, when operating. the cause of the whining and knocking noise, was worn out grommets and bearing going bad in the motor. I reassembled everything in reverse order, being very careful not to get cut or burnt on the fins and tubing in the back of the freezer. Do not drop any thing down the drains while removing and /or reassembling, those items will cause lots of havoc to the lower fan and motor for the refrigerator, lay a towel in the bottom when you start working on it.. I then plugged it back up and there was on noise, works great.

took apart stat. area rplaced wire harness &t.stat simple but im a retired union electrican so wiring was a bit easy