GTS18DCMCRWW General Electric Refrigerator - Instructions

Removed the old water valve from back of refrigerator by using a screwdriver. Pulled water line off old valve that runs into the fridge and inserted it into the new part. I used a pair of pliers to take off water line that runs into the water valve from the house. Screwed the water line back onto the new valve. Took about 10 minutes.

Pulled the fridge from the wall. Then shut the water line to the fridge off. Pulled the water line to the ice maker out the old grommet. Then a screw or two from the cover over the bottom back of the fridge, so I could get to the outlet valve kit. Only 1 screw was holding that. Then took the lines off the old outlet valve. Took the little hose off the grommet on the inside of the freezer that leads the water into the drip pan to the cube tray of the ice maker. Then grabbed pliers for the grommet on the top back of the fridge. And pulled and twisted alittle till it came out. It was alittle hard but got it out. Cleaned the out sticky tape off around the hole where the grommet connects. Hook the water like that goes to the grommet for the ice maker to the new grommet. Peeled the paper of the sticky tape for the new grommet. And placed it in. Then connected the rest of my water lines to the inlet valve. Put everything back the way it was. Then plugged and turned the water back on. And in 2hrs or so I had ice fall in the tray and continues to make ice no problems. “Note also I didn’t actually unplug my fridge I did it all why it was plugged. Thought it would be best to let you know. LoL but a small socket 1/4 with a 1/4 drive or worked. Also I think my grommet was harder to get out cuz it was froze due to the water leaking in the grommet.

After determining that the ice maker on this relatively new refrigerator would make ice cubes if it received the proper amount of water. Ordered the valve and received in a couple days. Using a nut driver, removed the cardboard cover from the back of the refrigerator. Removed one screw holding the valve bracket to the fridge and removed another screw holding the water supply line and the water line to the ice maker in place. Pulled plug on fridge and removed 2 wires from valve. Removed inlet and outlet lines from old valve and reversed the process installing the new valve.

Other than having to bend the bracket 90 degrees it was an easy install.

Unplug refrigerator and turn water supply off to the ice maker. Remove the screws holding the bottom cardboard-like cover from the lower back of the refrigerator. Remove the water supply line to the old solenoid with 1/2 inch wrench. Unplug the two power supply wires to the old solenoid. Remove the screw that holds the solenoid to the back panel of the unit. After the solenoid is pulled out, remove the output hose with a 1/2 inch wrench. The configuration of the replacement solenoid is likely a little different than the original, but it seems to be rather universal and will fit back into place and perform properly. The new solenoid does not use a compression type nut to secure the output line. It's just a simple push-in connection. The wires may have to be rerouted a little, just keep them clear of the evaporator fan blades Reverse the removal procedure and you're done.

i took the backing off with a screwdriver, cut the wires and put the 2 wires on that came with the thermostat. p.s. make sure you pull the power plug before you start.

Tried replacing water valve since no water in ice cube tray. Exact part not available due to age of refrigerator, but I got the equivalent replacement part for $18. Mounting holes different, but I made it work. Also one connect on new one slip connect whereas both compression fittings on old valve. I put it back together and icemaker now works great.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

Just had to replace Vegetable Pan Cover-Simple repair-Fast service on part. Ordered on line one day, received part next day. Excellent service on my parts order. Thank you.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

Three easy steps, take off old part then all you do is tighten nut on one end of part and then just push other end of pipe down in slot. Did half to remove nut off the top end of tube very simple to do

easy - replaced it

i am totally impressed with your company how effective it is.... i will go to yours if anything is broken or replaced

thanks

I must thank yo for sending the fan so fast. If I ever have to deal with any appliance again, you are first on my list.

Remove the rear cover, shut off the water, removed the hose, unplugged the electrical connector, removed the screw holding the valve on. Removed the plastic tube going into the freezer and reversed the steps