ZISW48DXA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from Cocoa Beach, FL
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The silver plating on the auger was coming loose, rusting and getting in the ice cubes.
All I had to do was remove four (4) screws from the old ice bucket assembly to remove the front cover and attach it with the existing screws to the new ice bucket assembly. It was a very simple repair. Thanks for the expedient delivery and the exact replacement part that I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leticia from El Paso, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Ice Bucket had rusted
It was really simple, remove 4 screws form the old cover and put it on the new bucket. Simple, Simple!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THEOTIS from CHARLOTTE, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator COnstant running and low ice output
I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Canyon Country, CA
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My Auger was rusted, and discontinued. Had to buy complete Ice Bucket assembly.
Washed new Ice Bucket assembly with dish soap and warm water, and let dry. Removed (4) small screws holding Ice Bucket Door assemby to my original Ice Bucket assembly. Reinstalled Ice Bucket Door assembly to new Ice Bucket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Temecula, CA
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The auger in the ice bucket was rusted
Removed 4 screws from the old rusted ice bucket ( they hold the cover on) installed the cover and screws in the new ice bucket and installed the new unit in the freezer .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Pasadena, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice/Water dispenser freezing/clogging
I followed the Video on your website and that made it so easy and simple to follow. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Punta Gorda, FL
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad odor and rusty ice cubes. Auger had rusted and should have been covered by GE
Removed the old ice bucket assembly and dumped the contents. Removed four screws from the face plate and reinstalled it to the new ice bucket kit. Back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Chester Springs, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper was warpped
Follow instruction on the video you provided
Was this instruction helpful to you?
Thank you for voting!
Rusty Auger
The parts recommended were exactly what I needed. The comment section on not paying attention during the removal were very helpful. I took a picture before totally taking everything apart. Thanks for the added comment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Bridgewater, NJ
- Parts Used:
- WR17X3089
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice dispenser had a transistor failure on the control board
The solenoid in the dispenser was overheated due to the control board failure. After I rerplaced the board I found the heat had distorted the plastic crank and jammed the solenoid action. The plastic crank was easy to replace. Now after expending approx. $75 everything works normally!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Saint Johns, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Frost in ice dispensor
Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Nags Head, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
flapper was locking open periodically.
Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the interior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilbur from Brazoria, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
old ice maker was rusty had not been using it
order new augerand ice bucked changed face plate 4 screws now have good clean ice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Paso Robles, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Maker flapper
Your Video really made it easy, showing the actual replacment of the part. However I did have one problem, which was I could not unplug the panel just by pulling on the plugs. A locking catch is on each plug so I just moved the panel out of the way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Durham, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost build up in ice maker
Watch online video on how to change icemaker flap! Video was great exactly how to do it, with a link to order the part
Was this instruction helpful to you?
Thank you for voting!