PSB42LGRAWV General Electric Refrigerator - Instructions

Poped whole switch out with flat head screw driver. Removed wires with needle nose players and held the wires so they wouldn't get pulled back inside fridge shell. Attached wires to new part like a plug. Lights ccame back put new switch back inside wall. Shut door

1. Turned off water near hot water tank 2. Removed back (small section) of the refrigerator, only 7-8 screws. 3. Disconnected the old water hose (comes out easily. 4. Reconnected new water valve 5. Turned on water @ hot water tank 6. Replaced back of refrigerator. All done! I have never done anything like this, and I had no instructions, very easy to figure out. The part cost $48 here.

simply read the instructions

it was easy. Open the fridge,untwist the old filter. Open the new filter, fill with tap water and twist in place. Run water through it for a few minutes to insure it is working and filters the water.

Simple repair. I first shut off the water supply to the unit. I then removed back cover from lower part of the unit. The water valve is on the lower left side. I began by removing the screw on the bracket that holds the part in place. This screws into the back of the unit. I then disconnect the water line by unscrewing the fitting. Then unplugged the two electrical connections in the back of the unit. Lastly, remove the two hoses that plug into the bottom of the the unit. The installation was essentially the reverse of the the removal. The whole process took about ten minutes.

This repair is EXTREMELY easy to conduct even for the novice. The first step was to shut off the water supply at the wall, and disconnect the power cord to the refrigerator. Remove the six panel screws to remove the lower back panel. On the lower left hand side is the water valve. This is connected by only one screw, so that was removed. Compare your new valve with the one you are removing to double check that the units are the same. Disconnect the inlet water supply line and connect it to the new unit. Disconnect the two water outlet lines from the old unit and connect to the new unit. Finally, disconnect the two power plugs from the old unit and connect to the new unit. These are all colored coded or different sizes, so there is no way to fowl this up! I just recommend disconnecting and reattaching one at a time so that you are doubly assured you are doing this correct. Reattach the valve unit back onto the side of the refrigerator. At this point, I turned on the power and water supply to check for leaks. Also, have someone run the water in the ront panel dispenser to ensure things are working properly. Once that is completed, reinstall the back panel and you are done. I did this project about two weeks ago, and things are working great now. Saved a lot of time and money by doing this job myself.

Followed the instructions from your site and they were perfect. Unfortunatly that wasn't the problem. It still doesn't work.

per the video - took off panel, remove the existing part, and replaced.

watched your video,went to work

1. Remove back cover from frig
2. Remove Double Outlet Water valve from frame
3. Place towel under valve, remove supply line to filter
4. Cut black and clear lines next to valve, ensure a smooth cut
5. Slide new connectors onto lines, press lines into valve firmly, make sure they slide in all the way
6. Slide connectors into valve locking into place
7. Re-connect filter supply line and re-connect valve to frame making sure lines are in the proper place
8. Replace back cover of frig, do not over tighten screws

I watched the video instruction and it was very easy to replace. took me less than 30 minutes.

After gaining access to the back of the refrigerator. I shut off the water valve and pulled the electrical power plug. I removed 6 screws from the access panel. I then removed 1 screw holding the water valve. I disconnected the electrical connectors. Disconnected the water inlet tubing with an adjustable wrench. I removed the water to the door and water to the ice maker by pushing in on the collar which released the tubing. I discarded the old valve and installed it in reverse order. Did not fix the problem. My next guess is the control module.

replaced double outlet water valve. Valve works as it should. Shipping was much quicker than I expected.

Unplugged fridge, and turned off water supply. Removed cover from back of fridge, followed the plastic tube down to water valve.
I unbolted the mount holding water valve in place, removed the input tubing on top by unscrewing nut. I made a note of which outbound plastic tubing went to water dispenser, and which one went to icemaker, and which side of the water valve they plugged into, and then cut the tubing very close to the old valve.
I slid the tubing into the new water valve, and I felt it lock into place, very easy. Attached the input water line and tightened the nut.
Reattached the water valve mount to the body of the fridge, replaced cover, turned water valve back on and checked for leaks (there were none).
Plugged in fridge, tested dispenser, everything worked just fine. No leaks.

turn water off to ice maker,unplugged refrigerator, took back panel off took old part off and put new part on