GSE25KETBFBB General Electric Refrigerator - Instructions

I visually inspected the compressor and narrowed down the source of the noise to the freezer area. Then I removed the doors and the screws securing the divider panel. Next I removed the bottom panel of the freezer, the styrofoam insullation panel and the evaporator motor. The motor is mounted between two grommets. I replaced the grommet facing the fan blades. The aluminum reflector below the styrofoam insulation panel had also come loose. I reattached it and reassembled the refrigerator in reverse order. The noise is gone!

Replace

pulled out broken bucket and auger assy. and slid in the replacement. works great so far. The easiest part was ordering the part and it didn't take very long at all to get it. Customer Service was very good at getting the job done. Thanks

I tried to quite the noisey evap motor with special liquid motor grease from Radio Shack. It did not work, so I ordered the evap motor. My freezer motor was wired slightly different than the motor I received. The replacement motor had a male plug attached to the four wires, the original motor was different, so I cut the wires and spliced them into the original freezer wires (colors were the same). Remounted motor. Works great, and no more groaning motor
Peter

I bought a Flapper replacement part from Parts Select. I installed it following their very complete on-line video directions. Their complete and easy to follow directions made my job very easy, and the work was completed without any problems and just as good as if it were done by a professional repair person. I am proud of my work, it couldn't have been done without their video insructions. Also I got delivery of the part within two days of my order. I will alway look for Parts Select any time I need an applicance repaired. Thanks to Parts Select!

Removed front panel (using small screw driver) by popping it out, disconnected wire from solenoid, removed solenoid which was rusted, 3 small philip head screws held it in place insereted new solenoid,connected wire snapped front panel back in. Clapper valve closes tightly and no frost in frezzer, saved my self a bunch of money.

To take the ice dispenser apart is not difficult. A ring removal tool would have helped to remove the auger. The Auger nut was difficult to remove and I used a visegrip to pull it off. Once the retaining ring was removed the repair was easy.
Never did it before but figured it out.

removed 4 screws in order to view and remove auger. removed metal and set washer on back of auger. This step not difficult. This will release auger from plastic ice resovoir. Again, not difficult. Remove plastic nut after removing auger. This procedure will release crushed ice blades and 5 plastic washers, 3 flat and 2 raised. You have got to remember order of blades and washer. Again draw diagram take pictures. Very, very important. Put back as taken apart. Good Luck

I removed the original shelf, took the glass portion off of the bracing and installed the replacement. The replacement was square and fit just fine so I installed it, put the shelf back on top and it works fine.
It was so easy to order the part through here. There were picture breakdowns so you could see exactly what you needed and order the correct part.

several times I had to remove the ice maker door solenoid due to it sticking. I ordered a new one from parts select. Problem solved!!!

The old cap was cracked and fell out easily. The new cap simply snapped into place. The part arrived very quickly and installation was a "snap".
My wife thinks I'm a Hero. I highly recommend PartSelect.com for fast and reliable service.

Removed the bottom front cover, under the two doors, unclipped the water line to have better access, removed old Union connector, cut about a 1/4' off each side of the line, pushed both sides of line in Union Connector, checked for leaks, all done.

just put them in the proper shelves

Watched a parts.com video on how to change defrost thermostat and followed the instructions

I removed the outer plate by sticking a very small screwdriver in the small holes at the bottom of the plate and pulling the plate toward me.
I then removed the 4 screws from the internal plate and pulled the plate toward me.
Then I romoved the 3 screws holding the old solenoid and unplugged it.
Next I put the new solenoid in place and replaced the three screws.
Finally I plugged in the solenoid and replaced the internal and external plates.