DTS18ICRERWW General Electric Refrigerator - Instructions

Pulled the fridge from the wall. Then shut the water line to the fridge off. Pulled the water line to the ice maker out the old grommet. Then a screw or two from the cover over the bottom back of the fridge, so I could get to the outlet valve kit. Only 1 screw was holding that. Then took the lines off the old outlet valve. Took the little hose off the grommet on the inside of the freezer that leads the water into the drip pan to the cube tray of the ice maker. Then grabbed pliers for the grommet on the top back of the fridge. And pulled and twisted alittle till it came out. It was alittle hard but got it out. Cleaned the out sticky tape off around the hole where the grommet connects. Hook the water like that goes to the grommet for the ice maker to the new grommet. Peeled the paper of the sticky tape for the new grommet. And placed it in. Then connected the rest of my water lines to the inlet valve. Put everything back the way it was. Then plugged and turned the water back on. And in 2hrs or so I had ice fall in the tray and continues to make ice no problems. “Note also I didn’t actually unplug my fridge I did it all why it was plugged. Thought it would be best to let you know. LoL but a small socket 1/4 with a 1/4 drive or worked. Also I think my grommet was harder to get out cuz it was froze due to the water leaking in the grommet.

unplugged the old valve and disconnected the water line, then reconnected water line on new valve and plugged it in. It was an easy process but unfortunately that did not fix the problem. It is the ice maker it self so I will be ordering a replacement ice maker.

I must thank yo for sending the fan so fast. If I ever have to deal with any appliance again, you are first on my list.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

Remove the rear cover, shut off the water, removed the hose, unplugged the electrical connector, removed the screw holding the valve on. Removed the plastic tube going into the freezer and reversed the steps

easy - replaced it

i am totally impressed with your company how effective it is.... i will go to yours if anything is broken or replaced

thanks

I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.

Three easy steps, take off old part then all you do is tighten nut on one end of part and then just push other end of pipe down in slot. Did half to remove nut off the top end of tube very simple to do

i took the backing off with a screwdriver, cut the wires and put the 2 wires on that came with the thermostat. p.s. make sure you pull the power plug before you start.

Tried replacing water valve since no water in ice cube tray. Exact part not available due to age of refrigerator, but I got the equivalent replacement part for $18. Mounting holes different, but I made it work. Also one connect on new one slip connect whereas both compression fittings on old valve. I put it back together and icemaker now works great.

Removed old valve easily. New WR57XI0033 valve is designed to mount on lower left, but on mine it has to mount on lower right. Had to drill two 1/32 holes in lower rail to mount the new valve.

-Empty the freezer
-Take the cover in the back of the freezer off
-Melt the ice off the coils (heat gun, hot water, etc.)
-Cut the wires off the old sensor and connect the new sensor using a soldering iron or some other method.
-Cover the spliced wire with heat shrink, electrical tape or some other method.
-Reassemble the cover

Done!

Removed icemaker from freezer,
Removed 3 screws from cover plate, and removed screw securing main gear, removed gear.
Pulled back cover plate to expose switches and mechanism.
Removed screw holding switch to remove switch, and installed new switch.
I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install.
But it works!