Models > TBX25PRYERAA > Instructions

TBX25PRYERAA General Electric Refrigerator - Instructions

Jump to:

All Instructions for the TBX25PRYERAA
31 - 45 of 151
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Phyllis C. from Northwood, NH
Parts Used:
WR17X2769
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Slide rail broken at forward mount
Took out shelf & brackets. Removed plastic shelf. Unscrewed broken bracket & screwed in new bracket.
Put back in & replaced the shelf.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Winston from BRONX, NY
Parts Used:
WR24X437
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
leaking water from casket seal
Remove old gasket by pulling out one corner at a time and Installing it by placing it in the grove.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jorge from Spring Lake, NC
Parts Used:
WR17X2769
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
broken right side rail.
I had to remove the glass shelve, the two drawers, and the middle rail. Once I did that, I slide the unit out together. I placed the unit on the floor and removed the one screw located on the far backside of the unit. I had to remove a slip cover (it had the kenmore logo and the writting on it) it was a snap on, so no problem. Glad it was not gluded on. After the old part was removed, I put the new part on. Put the two screws back on and snap the cover back on. Then I put the whole unit back in. This included the glassshelve and drawers. The process was pretty easy. Good luck with your change.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Philip from S BURLINGTON, VT
Parts Used:
WR17X11653
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Remove front cover
Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Rogers, AR
Parts Used:
WR17X11653
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Watched video on flapper assembly replacement looked real ready. Video failed to mention ice dispenser trim was glued in place . Had to buy real small paint scrapper that would fit in dispenser outlet to free inside edge of trim piece. Once I got it all loose job went very easy.
Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joe from BRICK, NJ
Parts Used:
WR17X11653
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
I just followed the instructions on the video and it was exactly as they said......no surprises.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stephanie from DENVER, CO
Parts Used:
7C7
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
drum light burned out
removed the bulb from the package unscrewed the old bulb & screwed in the new bulb.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jimmie from Surprise, AZ
Parts Used:
7C7
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Bulb burned out.
Screwed new bulb in socket
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Catherine from SEATTLE, WA
Parts Used:
40A15
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carl from SAN MARCOS, TX
Parts Used:
WR17X11653
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Ice Maker Leaking
Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rudy from CITRUS SPGS, FL
Parts Used:
WR17X11653
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Had a drip which filled up the tray and leaked on the floor from water dispenser
There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Peter from HAZELHURST, WI
Parts Used:
7C7
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The light bulb in my freezer door burned out.
Remove the burned out bulb and install the new light bulb.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from Chesapeake, VA
Parts Used:
WR17X2770, WR17X2769
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Left drawer slide broken replaced both right and left
Removed drawers and glass shelf. Removed screws that hold old slide rails in place. Installed new rails and re-installed cover for vents. Placed assembly back in and installed drawers.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alex from Cary, NC
Parts Used:
WR17X11653
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Frost buildup in freezer by the ice maker
Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
WALTER from SPRING HILL, FL
Parts Used:
WR17X2770, WR17X2769
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
original parts broken (poor design)
Unscrewed four screws, two on each part, and replaced broken parts, reinserting screws. This is a no-brainer repair.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the TBX25PRYERAA
31 - 45 of 151