MSX27HRBWH General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- jimmy from saluda, SC
- Parts Used:
- WR17X2740
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
would not dispence ice
remove ice bucket and replace broken augar
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from sweeny, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
no water to ice maker or water dispencer
replaced circuit board and water solenoids
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilbur from Brazoria, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
old ice maker was rusty had not been using it
order new augerand ice bucked changed face plate 4 screws now have good clean ice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Corpus Christi, TX
- Parts Used:
- WR49X10183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rust in ice
Replaced auger and front helix kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Joliet, IL
- Parts Used:
- WR62X23154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice maker- wouldn't release cubes only crushed ice.
Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GENE from ASHEBORO, NC
- Parts Used:
- WR62X23154, WR62X26536, WR62X26536
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No cube ice. We had crushed ice.
Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Colorado Springs, CO
- Parts Used:
- WR71X1936
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing a shelf in freezer
I saved about $15.00 by ordering the part on line. It came in about a week and was a super easy process. Since it was just missing there really wasn't anything that needed fixing. just installed it where it belonged and all was good. Great and easy experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Paducah, KY
- Parts Used:
- WR30X256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Collar that holds Ice auger assemble was Broken.Seems to be a manifacturing defect in this model.
I simply ordered a new Ice bucket, removed about 6 Phillips head screws, removed the old bucket from the Ice door and replaced with a new bucket. SIMPLE !!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from Catharine, KS
- Parts Used:
- WR17X4312
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Needed complete ice bucket assembly
Since Parts Select was unable to cross reference to another part I myself checked out all other web sights and did my own cross reference. I found a matching compatable ice bucket number and bought that ice bucket from part select I got it quickly and put it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Jacksonville, FL
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Auger and Ice Bucket for GE side by side was rusty
followed the previous posts, loosened four screws on the front panel, attached panel to new auger and ice bucket, and was good to go. Excellent advice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from Argyle, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rusty auger tainting ice
It was so easy! I seldom attempt any household repair because I have a husband that can fix anything, but he was not available. One screwdriver & remove 4 screws attaching the existing front to old auger/bucket. Line up the screw holes on new bucket with old front, put the 4 screws in through those holes tighten screws & I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Colleyville, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
auger and bucket neded to be changed because of rust which caused the auger and other metal parts to rust which created an unpleasant odor in ice and freezer. to
The part arrived promptly but was defective. Upon learning of the problem by PartSelect a new part was shipped and was delivered incredibly quickly. Installing it was easy and took only about 5 minutes. We were pleased with the speed in sending the parts and the ease of installation. We will call on them again if necessary because of their good business practices.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe F. from Kountze, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice crusher was broken, putting plastic in ice.
Ordered Auger and Ice Bucket Assembly All I had to do was install 4 screws. Worked great. Thanks.Joe
Was this instruction helpful to you?
Thank you for voting!
rusty icemaker, broken light shield
1) Unscrew the old ice maker from the ice bucket and remove. 2) Add the new auger and screw back into the ice bucket. 3) Ta Da. No more rusty ice cubes! The Ice schield you merely insert the tabs into the slots in the freezer. Parts all seem to fit fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Collierville, TN
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice bucket assembly broke
Ice bucket and auger came fully assembled. Just had to attach the face plate from the broken ice bucket assembly and slide it into the freezer. There were only four Phillips screws involved.
Was this instruction helpful to you?
Thank you for voting!