TFG22JABCWW General Electric Refrigerator - Instructions

This is a side-by-side unit. After blocking up the closed refrigerator door to the correct height to match the freezer door, I removed the lower hinge pin assembly by taking out two bolts. Save the shims (my had two) for the new hinge pin. Then remove the cam riser from the bottom of the door by taking out two bolts. Install the new cam riser on the bottom on the door. Then install the new hinge pin assembly. Total time 15 minutes.

blocked up refrigerator door.removed old hinge, and put new one on,with socket set.

shimed the door up to its proper level. removed plastic cam from bottom of door with a socket disconnected the water line fitting and clamp. with a nut driver removed the hinge assy from cabinet being careful i sled the hinge assy off the plastic water line being sure not to kink the line, sled the new hinge assy back on the water line and mounted the new hinge assy to the cabinet and connected the water line back up and turned on the water and checked for leaks, all went well. place the bottom grill cover back on.

Followed directions in your video. Very helpful. Be certain to pay strict attention to how old part is removed. Had a little trouble replacing door on lower pin/hinge. Helps to have a little assistance. Good suggestion from another customer: get the kit.

Several months ago I had to replace the hinge and cam on the refrigerator door and the repair went smoothly as pictured in the video. This time I had to replace the cam on the freezer door so I ordered the hinge assembly, which included the cam. The web site confirmed that, according to the model number of my 27 year old refrigerator, the hinge assembly would fit. The problem I had was that the top hole in the hinge was positioned too high to fit the hole in the refrigerator so I had to put the old hinge back on, even though it showed some wear. The door closes smoothly by itself now.

on the refrigerator side remove two screws from hinge on top of door, pick doorup to remove from bottom hinge using a 5/16 socket remove the two screws holding hinge in place, replace with new hinge. on the door loosen up the screws, no need to remove. the screw closest to the hing axis remove completely remove the old cam, insert new cam lined up with axis of hinge reinsert screw, place door back on hinge and replace hinge on top. the freezer side has water an ice in the door.at the bottom [grill has been removed] of the door a plastic tubing has to be disconnected [make sure water is off] the disconnect is near the door, the coupling is only finger tight. uncou[ple plastic coupling and pull out of connection, pull the nut and ferule off the tubing. now take top hinge off, remove door straight up while feeding plastic tubing thru hinge. the hinge is replaced the same way as the other side. when new hinge an cam are in place, lift door up now feed the plastic tubing thru the hinge till door is in place, replace top hinge. when you reconnect the plastic tubing it helps if you place a lubricant on the end so that you slide the nut and ferule on. the connection should only be finger tight, no wrenches

Removal was easy. The problem was that the old hinge had screws approximately 3/4 inch apart. The new hinge assembly had screws 1 inch apart. The threaded backing plate matched the 3/4 inch spaced old hinge but would not line up with the new one. There was a hole in the refrigerator frame but no way to hold the screw from the back. I had to fine a bolt and nut that would fir and still be heavy enough to hold the weight of the door. This repair took place at my cabin--miles from any hardware store. I found a long enough bolt and nut but it was a little too big for the hole in the hinge. I had to drill the hole in the hinge out so it would fit. Trying to reach the back of the bolt with a nut was a problem. I used tape wrapped backwards on my finger to hold the nut and then reached around to start the bolt into the nut. It too a few tries but I finally got it. Bottom screw was not a problem. It took about an hour and a half to fix the door but it works fine now.

I removed all the items off the shelves of the door. I then removed the top assembly,Then lifted the door off the the bottom hinge and laid it on a flat surface. I then removed and replaced the cam connector on the bottom of the door. I then removed and replaced the cam from the lower right side of the refrigerator. I put the door on the cam without assistance , then reassembled the top assembly. The refrigerator door operated immediately just like it did when it was new over 20 years ago.

I just followed the video instruction supplied by PartSelect and the whole thing was a breeze.

I replaced both bottom hinges on my GE refrigerator. The hint that they were worn out was that both the freezer door and fresh food door would not close completely. You had to lift the door on the hinge to get it to close. Many of the GE service repair people recommend complete removal of each door to replace the bottom hinge. I found I could use a couple of wood blocks tall enough to take the weight of the door, jacking it up off of the hinge so could loosen the hex head screws. The freezer door hinge took a few minutes longer because the water supply line for the icemaker which is routed through the tube in the hinge. Overall, an easy repair and the cost of two repair visits was saved.

There were some great posts on similar repairs that made me realize that it was best to get the whole hinge assembly. The video regarding the repair was completely accurate down to the size of the socket wrench required.

As suggested by your web site. Thanks. BC

Noticed hinge cam riser broken in 3 pieces. Took fridg door off, 3 screws on top. 2 screws on bottom loosend one screw and removed other screw. replaced cam riser and reassembled. Wife helped.

Watched PartSelect video and did exactly as video said. Had finished product in less than 30 minutes.6 bolts and one screw.

Replaced the gasket and the hinge assembly. Replaced the hinge assembly on the freezer door as well since it was worn. YOU DO NOT NEED A DREMEL to cut anything. People doing that are trying to save $10 but don't do it. Just order the hinge assembly. It comes with the loose cam riser and the second cam riser that is attached to the hinge. DON'T CUT ANYTHING. Super easy. I prepped the door for the hinge replacement the night before. Removed fridge magnets, etc. Moved everything from inside the door to the shelves. Got home from work (package was there in two days, fast) and it took 5 minutes for the Fresh Food Door hinge replacement. Removed hinge cover, removed 4 hex screws (two on top and two on bottom). Swapped hinge and cam. Be sure to use the cam that came with the hinge. Always replace in pairs. Freezer was more tricky. Turned off water. Had to remove a clip (small phillips head screw) on the white tubing. Unscrewed plastic nut. Pulled off spring from tubing. Set spring, nut, and clip with screw aside. Removed hinge cover, unplugged electronics, removed 4 hex screws (two on top and two on bottom). Swapped hinge and cam. Super easy.