TFG22JABCWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rick from Yadlley, PA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Door would not close on its own
I removed the top hinge, lifted the door off the bottom hinge, rmoved and replaced the bottom hinge assembly, and reinstalled the door. I then aligned the door and reinstalled the upper hinge. The fridge works just like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Grand Haven, MI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Freezer door would not close,and would pop open if refridge side door would close
After recieving the part overnight (Very unexpected speedy delivery!) I propped the freezer side door up with a 4x4 and 2x4 and the old part came right off and the new part went right on with no hassels, Done in less than 15 min!!!!
The new part even came with step by step easy to follow directions.
The new part even came with step by step easy to follow directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorrie from Russellville, AR
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Door dropped. Cam riser was gone
Emptied the refrigerator door so it was easier to take off. Used a screwdriver to remove the screw on the top hinge. Lifted door off bottom hinge. Laid the door down so I could take the bottom hinge off. Removed worn out parts and placed the new one on. Slipped door back on hinge,made sure it would close properly and was lined up with freeze door. Put top hinge back in place. Done!! Now door finally shuts on its own again!!! EASY!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from bayville, NY
- Parts Used:
- WR02X10140
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
cam britle door down to metal
remove plastic top hinge cover then twoscrews holding door with door closed it rested against freezer door then lefted off door put on flat surface remove tow screws at bottom of door installed new cam
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Holbrook, NY
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door closing cams, top and bottom, became damaged and needed replacement
Turned refrigerator off. Removed food from right hand (refig.) door. Closed door. Removed upper hinge cover with a standard Phillips screwdriver and then removed upper hinge by removing two 5/16" bolts using nutdriver. Lifted door up to clear the bottom hinge-post and set it on the table. Removed the kick pan at the bottom of the refrigerator and then removed the bottom hinge-post which was attached with two more 5/16" bolts. Installed new lower hinge post and rubbed a small amount of mineral oil on the closing cam (which is riveted to the hinge-post). Removed the old upper closing cam from the door (5/16" bolts) while it as lying horizontal on the table and installed new cam lubricated with a small amount of mineral oil. dropped the door in place, replaced upper hinge and cover. Replaced kick pan. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- henry a from pennsauken, NJ
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
bad door hinge and cam
parts ordered fit perfectly made repair removed items from shelves removed door avd replaced hinges and reassembled 1/2 hour total by myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Woodstock, GA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door would not close properly.
Removed door and replaced bracket assembly. Door works like new. Self closing and sealing properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from hillsboro, NH
- Parts Used:
- WR02X10140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Cam Riser worn out
very easy, thanks for the great selection for parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zach from Glenwood Springs, CO
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door wouldn't close and open properly
Removed guards and covers, (2 snap connections, 3 phillips head screws) Removed two 5/16" screws, removed door, removed cam from bottom of door, installed new items.
Worked Great!!!
Worked Great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Coventry, CT
- Parts Used:
- WR02X10140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Cam riser broken
Removed trim cap at top of door. Removed two hex head screws and lifted top hinge off door. Lifted door off lower hinge. Unscrewed broken cam riser from bottom of door and replaced with new part which was then screwed into place. Replaced door on lower hinge, Replaced upper hinge onto top of door, replaced screws and replaced trim.
Easy peasy. :-)
Easy peasy. :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Austin, TX
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The cams that allow the fridge door to automatically close had worn out
First I bought the right tool to remove the hinges.
Then replaced the hinge with the two cams.
Now the door closes itself.
Then replaced the hinge with the two cams.
Now the door closes itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from lesage, WV
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door stop broke
they sell the cam piece but the instructions says not to replace only one part. so beware you need both the cam and hinge as a kit .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Warren, VT
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Plastic cam at the bottom of the door disintegrated so door won't shut
1.Emptied the stuff from inside of the fridge door.
2.Using a phillips screw driver I removed the plastic cover over the top hinge.
3. Using a small ring spanner I removed the two bolts holding the top hinge (pin), removed the hinge and lifted the door off the bottom pin.
4.Using the same spanner I removed the bottom hinge containing the broken plastic cam.
5.Replaced the broken hinge with the new one and put a little grease on the hinge pin.
6.Placed the new plastic cam on the hinge pin and refitted the door.
7.Replaced the top hinge and plastic hinge cap, Job Done!
A couple of points a) When your plastic cam needs replacing, always buy the hinge pin & plastic cam. The pin has a plastic cam welded to it and as this is the partner of the plastic cam it will also be worn so you should replace them as a pair.
b) You will spend more time cleaning the 'out of the way' parts of the fridge than actually carrying out the repair.
My fridge is now as good as new.
2.Using a phillips screw driver I removed the plastic cover over the top hinge.
3. Using a small ring spanner I removed the two bolts holding the top hinge (pin), removed the hinge and lifted the door off the bottom pin.
4.Using the same spanner I removed the bottom hinge containing the broken plastic cam.
5.Replaced the broken hinge with the new one and put a little grease on the hinge pin.
6.Placed the new plastic cam on the hinge pin and refitted the door.
7.Replaced the top hinge and plastic hinge cap, Job Done!
A couple of points a) When your plastic cam needs replacing, always buy the hinge pin & plastic cam. The pin has a plastic cam welded to it and as this is the partner of the plastic cam it will also be worn so you should replace them as a pair.
b) You will spend more time cleaning the 'out of the way' parts of the fridge than actually carrying out the repair.
My fridge is now as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Camarillo, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Door wouldn't automatically close, dropped a bit
First removed plastic cover off top hinge with phillips screwdriver. Used nut driver to loosened screws on upper hinge to 1/2 inch out and then used wood blocks to shim up door as high as possible while still in closed position. Used socket wrench to remove lower hinge and fitting from bottom of door, while still closed. Installed new lower hinge and door fitting with socket wrench. Lowererd door to sit on bottom hinge and then adjusted position of top hinge before tightened those screws with nut driver. Reinstalled plastic cover. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Millersville, MD
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
HInge Cam Riser next to lower door hinge broke and door would not close
The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.
Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.
Easy job .. around 20 minutes.
Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.
Easy job .. around 20 minutes.
Was this instruction helpful to you?
Thank you for voting!