PTE25SBTARSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tina from Beaumont, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was not making ice.
First i removed two screws that holds the ice maker in, unplug the plug to the ice maker. I was able to remove the old one. Place the new one in screwed in the two screws and pluged in the plug and in just a little while i had ice again. I am a women, if i can do it any one can. I had a repair man tell me it was going to be $250.00 dollars to replace it. I got on line ordered the ice maker and had it in 4 days. Very fast shipping and easy to install. Tina Kearns Beaumont, Calif
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rafael from New Haven, CT
- Parts Used:
- WR50X10068
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
ice on the frezer compartment
turn off the refrigerator,then open the cover and saw lot of ice. then get a hair dryer blower and blow a heat to melt the ice. cut the thermostat defrost.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Wylie, TX
- Parts Used:
- WR60X10185
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
whining noise from freezer
had to remove ice maker and several panels to get to the fan. wires for fan encapsulated so had to cut old and new wires then solder them together while working inside the small freezer area. not too bad all in all took about an hour to get it done. no more wind thru the trees noise and is working fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mahvash from Gold Canyon, AZ
- Parts Used:
- WR50X10068
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Refridgerator warm, some ice buildup apparent in freezer
Find online diagram of freezer section for reference. Disconnect power, remove evap cover plate (214) by removing one of the drawer guide rails.
As evidence of your problem, you might see a giant block of ice built up around the coil. Let this defrost this before continuing.
Find THERMOSTAT DEFROST (24) sensor and clip connecting wires. Match replacement sensor wires by color. Twist and solder wires; or wire-nuts and twisting alone might be okay. If not soldering, seal the wire-nuts connections from moister with a good sizeable piece of duct tape. Make sure your wires are out of the way and not left dangling on the evap heater coil, where they could melt.
Suggest concurrent replacement of evap fan motor if this has not already been done in the past.. This become noisy with age and damage from the ice build up seems to have made mine worse.
As evidence of your problem, you might see a giant block of ice built up around the coil. Let this defrost this before continuing.
Find THERMOSTAT DEFROST (24) sensor and clip connecting wires. Match replacement sensor wires by color. Twist and solder wires; or wire-nuts and twisting alone might be okay. If not soldering, seal the wire-nuts connections from moister with a good sizeable piece of duct tape. Make sure your wires are out of the way and not left dangling on the evap heater coil, where they could melt.
Suggest concurrent replacement of evap fan motor if this has not already been done in the past.. This become noisy with age and damage from the ice build up seems to have made mine worse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Tulare, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No ice in hopper
Ice hopper had no ice in it. But water in door worked and if I added ice to hopper, it would dispense in door. I added water to ice maker but no ice was made. Replaced ice maker and all it required was to unplug harness and remove two screws with nut driver. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Elkton, MD
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice Maker Leaked Water
Removed Ice Maker (2-Bolts)
Removed Ice Tray Screw Motor (to get to Ice Maker Plug- 4 small screws)
Installed new Ice Maker and reinstalled Ice Maker Screw Motor
Extreamly easy
Removed Ice Tray Screw Motor (to get to Ice Maker Plug- 4 small screws)
Installed new Ice Maker and reinstalled Ice Maker Screw Motor
Extreamly easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Mahomet, IL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The ice maker needed replacing for a couple of years. Then, a couple of weeks ago, the water supply stopped serving both the ice maker, and the drink dispenser.
I ordered both a new replacement ice maker, and a new solenoid/pump. They were delivered to my house within one day and I had them installed in a matter of an hour. I had to use the power extension cord supplied with the ice maker.
The new "quick connect" hose couplings on the new pump are great.
The new "quick connect" hose couplings on the new pump are great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Riverview, FL
- Parts Used:
- WR60X10185
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Whirling noise coming from freezer section
1) remove the ice bucket. 2) remove light cover and bulb. 3) remove back panel with 2 screws. 4) remove fan shield. 5) unlug 2 elec connections. 6) remove fan housing. 7) extract wiring grommet and use exacto knife to slice thru grommet along the length of it to release wires. don't cut light wires. 8) cut up old fan/light electrical plug to free wire nubs for light. 9) install nubs in new fan plug. 10) remove old fan motor, pull blades. 11) install blades on new fan moter and install fan into housing. 11) reinstall
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William E. from Centennial, CO
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old ice-maker went SOUTH
If a 74 year old guy can install an ice-maker in a 20 + year old fridge in 20, or so, minutes it must have had good pictures and BIG PRINT. Working quite well at this time!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from new city, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ICE MAKER gave out after 20 years
TURN WATER OFF TO REFRIDGE. TURN OFF ELECTRICITY.
Remove old ice maker (AFTER REMOVING THE BIG ICE TRAY) by disengaging two philips head screws but don't totally unscrew them. You must then totaly unscrew the bottom screw below the top two screws. Unplug the 5 head connection. (electricity)
Use adapter for the electrcity, etc from the box, (five head connection) Use the old plastic hose to hit the new cup. TIGHTEN TOP SREWS. LEVEL BY EYE. Turn the system on. Prime with some fresh water.
PS make sure that the light is on (green) and you will be in ice city. Be careful not to disengage the elcectic head when replacing the big ice tray.
HAVE A COCKTAIL!
Remove old ice maker (AFTER REMOVING THE BIG ICE TRAY) by disengaging two philips head screws but don't totally unscrew them. You must then totaly unscrew the bottom screw below the top two screws. Unplug the 5 head connection. (electricity)
Use adapter for the electrcity, etc from the box, (five head connection) Use the old plastic hose to hit the new cup. TIGHTEN TOP SREWS. LEVEL BY EYE. Turn the system on. Prime with some fresh water.
PS make sure that the light is on (green) and you will be in ice city. Be careful not to disengage the elcectic head when replacing the big ice tray.
HAVE A COCKTAIL!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Ulysses, KS
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old Ice quit working, would make ice but wouldn't flip ice.
Removed old Ice maker and replaced with new Ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Medway, MA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ice maker not calling for water to make ice.
I removed the screws that held the unit in place, and also the screws that held a plate that covered where the unit plugs in. I unplugged the unit, and removed it. Put the new one in, reversing the steps. Turned the new unit on, and had ice in 45 minutes! Summer is coming, I need my ice maker! This is the second unit I have replaced on this refrigerator, the first one was not releasing the cubes. This second one was a different style than the first, but same install process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from MITCHELL, IN
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Icemaker Wouldn't Totally Work
Loosened 2 screws unplugged cable. Plugged in cable adapter on new unit. Plugged in to receptical, hung on 2 screws, tightened 2 screws. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Greenbelt, MD
- Parts Used:
- WR50X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
defrost problem
I replaced the thermostat. I simply followed the insructions in the video on your website and it was done in about 5-10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Northville, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old ice maker quit
removed old ice maker, obtained part number from it. went on line ordered new ice maker at 10:45 in the morning, at 3:00 the nexte after noon new icemaker was in hand. took about 5 minutes to install new ice maker. works perfect. would do business again with this company.
Was this instruction helpful to you?
Thank you for voting!