GSG22KBMCFBB General Electric Refrigerator - Instructions

Unplugged the freezer. Then I gained access to the fan: remove the top freezer rack, remove the ice tray, remove the air flow manifold(needed to unscrew some screws), remove the manifold over the fan and cooling element. I unscrewed the fan mounting bracket. The fan motor's wires are plumbed through some plastic that i would have had to remove, so I decided instead to cut the wires and splice in the new fan motor. Then I put everything back together - the new motor works fine and doesn't make the whining noise.

Find online diagram of freezer section for reference. Disconnect power, remove evap cover plate (214) by removing one of the drawer guide rails.

As evidence of your problem, you might see a giant block of ice built up around the coil. Let this defrost this before continuing.

Find THERMOSTAT DEFROST (24) sensor and clip connecting wires. Match replacement sensor wires by color. Twist and solder wires; or wire-nuts and twisting alone might be okay. If not soldering, seal the wire-nuts connections from moister with a good sizeable piece of duct tape. Make sure your wires are out of the way and not left dangling on the evap heater coil, where they could melt.

Suggest concurrent replacement of evap fan motor if this has not already been done in the past.. This become noisy with age and damage from the ice build up seems to have made mine worse.

first removed two srews removed rear panel hair dryer to melt ice (took 30 minutes) cut two wires to thermostat spliced onto new part clipped it onto tube -done replace rear panel and 2 screws. very easy job after reading other letters and their experience -saved myself $500.00

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

took a little more effort than the video show to remove old module and replace new. Works fine now.

Took cover off, pushed blade on, and replaced cover

It was way to ez to install only a couple of minutes that's it

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

1) remove the ice bucket. 2) remove light cover and bulb. 3) remove back panel with 2 screws. 4) remove fan shield. 5) unlug 2 elec connections. 6) remove fan housing. 7) extract wiring grommet and use exacto knife to slice thru grommet along the length of it to release wires. don't cut light wires. 8) cut up old fan/light electrical plug to free wire nubs for light. 9) install nubs in new fan plug. 10) remove old fan motor, pull blades. 11) install blades on new fan moter and install fan into housing. 11) reinstall

I followed the instructional video. It was right on the money for accuracy in terms of part location and method of replacement.

I took the ice maker out then the panels that closes in the evaporator coil. Disconnected the defrost censer and tested it with an ice bath. The censer did not close the circuit. So it's bad. I got the parts .(Very fast I might add. The PartSelect team did a great job of getting it to me). I the stripped the wires and spliced the like colors back together and tested the censer again with an ice bath. It closed this time. I started the frig and have not heard anything from the client. In this case "No news is good news". Thanks PartSelect

Removed food from Freezer, Unplugged refrigerator. Removed light bulb cover and ligt bulb. Unplugged and removed Ice maker and motor. Removed air duct cover from motor. Unplugged and removed evaporator housing and fan. Pulled fan blade off. Unscrewed brackets from fan motor, removed dust cap from top of motor and grommet from bottom. New motor came with 6 pin connector and four pins for evaporator fan motor. Cut the harness grommet to separate the light bulb wiring from the evaporator motor's. Pushed the the old light bulb pins (red and orange) from old connector and push them in to the new fan motor connector. Reversed the process and no more noise

Refrigerator was showing actual temperature of 80 deg, freezer was about 3 deg high. (house temp was 65 at the time) Defrost heater seemed like the only component able to heat that much, so the defrost thermostat seemed like the likely culprit. I followed the installation directions in the video, and the fridge has been fine ever since.

I took off the back panel in the freezer. Located the wires going to the old thermostat, cut them with wire cutters. I then spliced the matching wires together and attached the part to the coil tube (There is a little clip on the part, be sure to do this because I forgot and had to go back and do this again!!!).

I ordered the part but my husband had to work out of town for a week. The fridge kept getting warmer, so when the part came I just watched the video on the internet, (bit the bullet) and did the repair just as I saw it done on the video. It was simple and exactly the same as the video. It took a little longer for me because there was a lot of ice built up on the coils, so I used my hair dryer to melt the ice. My refridgerator is working great now.