MSG22GRTCWH General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from Grand Blanc, MI
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door closing cam worn out
Removed refrigerator door and replaced bottom door pivot with the included mating cam and the door closing cam on the bottom of the door.
I didn't know that there were two mating cams and only ordered the door closing cam which I read online was the problem. It was the number one part on the part select list. The number two part was a kit including the door closing cam and the pivot with mating cam attached. It would have been helpful if there had been some notes that said check condition of both cams before ordering the part. So I have a spare door closing cam and paid an extra $19 including $8 shipping which negated a return.
The repair is easy - getting the right parts the first time is the trick.
I didn't know that there were two mating cams and only ordered the door closing cam which I read online was the problem. It was the number one part on the part select list. The number two part was a kit including the door closing cam and the pivot with mating cam attached. It would have been helpful if there had been some notes that said check condition of both cams before ordering the part. So I have a spare door closing cam and paid an extra $19 including $8 shipping which negated a return.
The repair is easy - getting the right parts the first time is the trick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from zion grove, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rubbeer flapper was worped causing frost in the freeze
The same as the vidio, very easy. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES R. from INDIAN SHORES, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Moisture seeping into freezer through ice dispenser
Removed ice dispenser trim from bottom-up and then removed control panel by gently pulling up from the bottom. Removed four screws holding dispenser chute and then two screws holing flapper assembly. Replaced gnarly old flapper with a new one and put all removed pieces back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gregory from ellerslie, MD
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door was uneven and wouldn't close tight
removed the door, installed the cam riser, and reattached the door. It took longer to remove the contents in the door than it did to install the cam riser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Atlanta, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost was building up inside the freezer just above the ice dispenser shute.
Followed the instructions and replaced the door recess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Arlington Heights, IL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost on the bottom of the ice bin frome warped rubber flapper
Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Wooster, OH
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Door closing cam (made of Plastic) just wore out with age and broke in half
Took the door contents out and put them on the counter, took the door off the hinges by unscrewing the 2 screws on the top of the Fridge and lifting the door off the hinge onthe bottom. Then laid down the Fridge on the kitchen floor and replaced the Door Closing Cam, keeping in mind the order of the 3 shims and other things on the bottom of the door. Simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from North Plainfield, NJ
- Parts Used:
- WR2X4901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Door Cam And Cam On Refridgerator Were Damaged
I did not realize I needed 2 cams to complete repair. Door cam was riveted in. I had to drill out rivet and replace with nut and bolt. Otherwise it went quite sommothly. At first I just replaced the cam on bottom of refridgerator but door was not quite right when closing. Further inspection showed the door had the other half of cam that also needed replacement. Needed 2 orders. Paid for 2 shippings.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HERBERT from Harlingen, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket was shot
took off the panel, took out 4 screwws, took out old flap, installed new flap, put screws back in , and put trim back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vincent from mahwah, NJ
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
door was not closing properly
Your vidio was Brilliant !!i just followed your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles M from Concord, NC
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Door Closing Cam broke
The bottom of the door was 5 " off the floor. A 2x4 block and a 4x4 block were pushed under the door and supported it while the water line was disconnected the hinge removed and the cam replaced. It was a simple fix and reading other people's experience made the repair so much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maxie from Omaha, NE
- Parts Used:
- WR17X3484
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken freezer light shield
I was amazed the part arrived the next day the installation was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Danville, VA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door dropped down and draging, would not close
Buy ( 2 ) cams !!!! removed hinge cover and hinge on top of the door, ( 2 screws )...lift door off of the bottom hinge and lay door on the floor, remove broken cam on bottom of door with nut driver, ( 2 screws ) , install new cam..... remove the bottom hinge off of the front of the refrigerator with nut driver, (2 screws ).... saw rivit off and remove old cam, install new cam and secure with new bolt and nut,... reinstall hinge back on bottom front of refigerator.....replace door back onto the bottom hinge.....install top hinge back onto the top of the door....replace hinge cover......done !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Naples, FL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Fridge door was not self-closing
Followed step-by-step instructions in previous post. Note that there are TWO approaches, both of which work.
Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)
Option 2) Order the entire hinge assembly (PS290199), which includes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)
We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.
Thanks to previous posters for excellent instructions!
Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)
Option 2) Order the entire hinge assembly (PS290199), which includes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)
We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.
Thanks to previous posters for excellent instructions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phyllis from owensville, MO
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Old Cam Had Deteriorated, And Was Breaking Into Pieces And Falling Off.
We taped the door with 3 pieces of duct tape, then put boards under it. Used socket set to remove cam and then cut off rivet so we could just use a screw to keep in place. . . Just for your information, I ordered 2 cams, and was glad I did as I need 2 to make the repair. . . Didn't read about this online or on order recommendation. The cams go 1 up and 1 down thanks for the installation repair stories, it inspired us to "do it ourselves " and we saved about $75 to $100. 00
Was this instruction helpful to you?
Thank you for voting!