GTS18DCMCRAA General Electric Refrigerator - Instructions

easy pry out, disconnect wiring, connect on new switch and press in switch.

I came home to find a mess near the refridgetor. My teenage daughter or son had made themselves a peterbutter and strawberry homemade jam sandwhich. The strawberry jam was all over the inside of the door and on the floor. What a mess, so I was waiting for my husband to change the gasket around the door anyways. So I though to myself I just change it myself. The old one just came off and I pulled the new one out of the box and I went right on with not much effort. ( I wiped down the area after I put off the old gasket) Thank you very much for making the parts so easily avaiable on your website without having to buy a new refrigator. Thanks again Sue and Ed

turn off ice maker Shut off supply to fridge unplugged fridge unhooked water supply line unplugged harness plug to valve.

I first disconnected the plug from the wall outlet. I then turned off the water supply to the back of the refrigerator. I then disconnected the two lines to the water inlet valve and removed the nut that holds the bracket to the refrigerator. I removed the water valve and installed the new one the same way in about 5-10 minutes. It was very easy, but, unfortunely that was not the problem.

Only took a screwdriver to take two screws out & install new slide with the two existing screws. Very easy. Took less than 5 minutes. Great website I found on Google right away, just by searching for refridgerator parts. After ordering part, only took a few days to come in.

Replacement of the single outlet valve kit went very well. But, water was still not dispensing. I checked if the valve was working by taking the following steps after installing the new valve: unplugging the refrigerator, disconnecting the water line from the underside of the new valve (line to the ice maker), putting a container under the valve to potentially catch water, plugging the refrigerator back in to start the cycle of the ice maker (remember that the cycle will start only if the temperature cold enough). I saw that the valve worked by dispensing water for a short period of time into the container. Taking my chances (with my limited experience), I disassembled the ice maker in the freezer and found that the water line was plugged with ice. So, I really didn't need to replace the valve after all. But, I'm glad I gained some experience.

Changed out the valve the water line hooks to in back of fridge and bingo that was the problem , less them 10 min job.

Replaced single outlet valve for the ice maker

With help from this site, It was one of three things. I thought it might be what this site suggested the most common and it was. the valve in back of refrigerator at bottom. Water comming to it, but not getting past. Ordered part. Was here in a few days. Real easy to change out. A few screw / bolts and one wire that fit only one way. I did have to bend new bracket to make it fit. Now have lots of ice cubes!

Replaced valve kit and let it run. Took a day for the fill line to thaw and has been making ice like a champ.

I ordered the valve, which came only a day later. Mine is really simple because it only has one water line and one electrical plug in. I do not have a separate water filter. First, I unplugged the refrigerator and shut off the water supply. I unscrewed the cardboard piece from the lower part of the back of the fridge and freed the valve. I pulled out the top water tube that goes from the valve to the top of the fridge, that connects into the back of the ice maker. That tube was empty and dry - I blew through it to make sure that it was unobstructed, and it was. No water was getting to that tube at all. I pulled out the plugs from the valve, and unscrewed the water line from the valve and let that drain in the bucket. I had drained as much water in the lines as I could by flushing a toilet and turning on the sink until it seemed the water supply that was left in the pipes was low. Then I just did the reverse putting together everything with the new valve. I screwed back in the water line that runs from the wall to the fridge. I pushed in the water hose line into the valve until it was all the way in. It was uneven and frayed at the end of that thin hose line, so I cut it very straight across the bottom so it would be entirely flush when it was pushed all the way into the valve. Then I inserted the plug back into the new valve. I put everything back in place, plugged in the fridge and turned on the water supply. I had left the fridge out off the wall so I could check for any leaking. I left it overnight and by morning I had ice! It was so easy. My only difficulty was pulling out the thin water hose from the valve. I did not realize that you can push down on the circular rim and the hose just slips out. I think I saved a lot of money.

water runs in now but still does not make cubes. just keeps dripping until I shut the water off.

replaced valve.

Googled the problem, came across this site where I learned what needed to be done to fix. Checked the part price, looked just for couriosity at the price from GE, it was WAY more expensive. Ordered the part, it arrived super fast, and shipping was next to nothing. The part came in, I replaced it. I made my husband so proud!!!

Connected the 2 wires and pushed in the switch until it clicked.