GTS18SBSSRSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cynthia from Clayton, NC
- Parts Used:
- WR32X10537
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken frame for crisper bins
Using Google search engine I was able to quickly locate the replacement rack for the refrigerator. When it arrived, I installed it by attaching it to the interior frame of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Oak Ridge, NJ
- Parts Used:
- WR32X10537
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf above vegetable drawers cracked in middle
Take out both vegetable drawers. Lift back of shelf first then front until you hear the click from both front sides. The shelf should now be loose and you can take fully out. Remove the glass shelf from the plastic frame by turning the shelf over and pulling back and up from the rear part of the glass. Put the glass into the new plastic frame by doing the same technique. Then put the shelf back into the fridge by the resting the shelf down in the correct position and pushing the front of the shelf until you hear the click again on each side. slide the drawers back into place and you are done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Seatac, WA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch wouldn't come out anymore and turn light on
Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Mansfield, TX
- Parts Used:
- WR01X10450
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Lost Set Screw
Took set screw and allen wrench and screwed set screw into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Farmingdale, NY
- Parts Used:
- WR55X24064
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both the fridge aqnd freezer would not get cold.
Easy. Followed the video instrucations. the part was right there next to the compressor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from District Heights, MD
- Parts Used:
- WR60X10172
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy evap fan motor
Simply unplug fridge, remove air duct mounted on rear panel, release panel itself, pull fan blade off, disconnect grounding wire, detach fan motor bracket, disconnect wire harness to release fan motor, install new fan motor and reconnect, secure with bracket, reconnect grounding wire, reposition fan blade onto motor shaft, reinstall rear panel and secure screws. Remount air duct and plug appliance back in. This is the second motor that was replaced since 2002. The 1st motor dies after 5-6 years.
Was this instruction helpful to you?
Thank you for voting!