TFX25CRYFBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DERICE from FARMINGTON, IL
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rust Flakes In Ice
Removed ice buscket from freezer, removed 4 screws holding front cover on, set aside old ice bucket, set new ice bucket in place and reinstalled screws, putback in freezer, done. Maybee ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Paducah, KY
- Parts Used:
- WR30X256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Collar that holds Ice auger assemble was Broken.Seems to be a manifacturing defect in this model.
I simply ordered a new Ice bucket, removed about 6 Phillips head screws, removed the old bucket from the Ice door and replaced with a new bucket. SIMPLE !!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Fripp island, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
3rd Flap for this Ice Mkaer, keeps warping
Very Easy, follow direction I the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald J from Seabrook, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flapper door mis-shapened
Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from social circle, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
frost formed because the ice damper let warm air into the freezer
Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ocean View, DE
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door flapper to ice needed to be changed
Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Spring, TX
- Parts Used:
- WR62X23154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator was only dispensing crush ice and not cubes
Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DON from ZELLWOOD, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Shute Flapper Was Distorted And Did Not Seal Opening Causing Frost Build Up
Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynwood from Spring, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
flapper was curled at one edge allowing air to enter and causing frosting in the freezer
I followed a video supplied with the e-mail notification of the shipment of the part. This was one of the best experiences I have had with locating, purchasing and installing a replacement part for an appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Benton, AR
- Parts Used:
- WR17X11653, WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flapper would not seal. Shield broken
Followed on line instructions. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Joliet, IL
- Parts Used:
- WR62X23154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice maker- wouldn't release cubes only crushed ice.
Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold E. from Hartselle, AL
- Parts Used:
- WR17X3095, WR17X10282
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
seal deteriotated preventing flappper from fulling closing, allowing escaping air to freeze up water line.
Snapped off the plastic plate covering the dispenser. Removed the four screws holding the mechanism in place. Remove the electrical connections. Pull the mechanism out and up carefully pulling the dispenser pad out with all the mechanism in place. Look at the mechanism before removing any parts to get a mental image so that reassembly will be easy. Remove any electrical switch or circuit boards and remove old parts before submerging the mechanism in hot soapy water for clean-up. The Clean-up will take longer than the disassemble and reassembling. After completion the dispenser works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ft Myers, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
air leak from ice maker flap permitting frost buildup inside ice maker dispenser
Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from Katy, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The rubber seal on the flapper came off.
My husband made the replaced the flapper while watching the video provided in your email, it was easy. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Fredericksburg, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Air leaking into freezer through door dispenser
I followed the video instructions. They were clear and consise. I removed the trim ring and controls. Them removed the housing and flapper. I did notice a small burr in the plastic chute and foam insulation. I trimmed this off with a utility in hopes this burr caused the flapper to warp. This is the 2nd time the flapper has been replaced in 1.5 yrs. The repair was really easy thanks to the video.
Was this instruction helpful to you?
Thank you for voting!