TFX20JABKWW General Electric Refrigerator - Instructions

I had this problem before and I knew it was related to the heater located in the freezer section. With the help of the drawings in the parts selct webpage I was able to identify the part I needed within 5 minutes. I ordered the part abd in 3 days I had it delivered.
I followed the instructions that came with the part step by step and I got my refrigerator up mand running in about 45 minutes.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..

Well, first I googled the problem and the model and found my way pretty quick to you guys. I sent a note to Tom P., who confirmed that I was looking at the right things. Then I offloaded everything from the freezer and fridge to the RV fridge and chest freezer, unplugged it and used my hair dryer to melt the ice on back plate so I could remove it.

I removed the two small screws at the top of the back, below the icemaker and light bulb, and slid the back cover up and out. Since my coils were pretty heavily iced, it took about half an hour to melt enough that I could get the defrost heater out and check it for continuity, which it failed.

The replacement design is slightly different (2 heater coils vs 1 and connectors on one end), but functionally the same. When putting the new one in, you need to re-run the blue wire down the same side as the pink wire because the connectors are on one end. Mine was long enough to work, but they include a splice kit in case yours isn't.

It took me longer to get the cover back on than to replace the heater assembly! Everything is back to normal, had ice cubes within a couple of hours...
Thanks for your help!

Removed panel, then removed single coil unit and replaced it with double coil unit that was sent to me. Refrigerator now working fine.

Parts select sugested checking the freezer side on the side by side if there was frost on the back panel. I took the back panel off on the freezer side inside the freezer. I found that the freezer coils were full of ice.Had to use a hair dryer to melt all the ice. The heater element was bad on the bottom of the freezer. I ordered a new defrost element an installed in 40 minutes and is running fine.You can still use the refrigerator until the new part comes in if you melt off the coils.It will last about 2 weeks.

1. Unplugged refrigerator from wall power socket.
2. Removed the 2 1/4'' screws and removed the back panel in the freezer section
3. Defrosted all of the ice off the coils and heater using a blower dryer which took about 10 minutes and lots of towels.
4. I replaced the defrost heater by following the provided instructions. I had a single element defroster which was replaced by a double element defroster. The instructions provided showed how to modify the wiring and were simple enough to follow.
5. Installed back panel and plugged in the refrigerator.

I checked on the defroster 1 week later and was pleased to see no ice on the coil. Problem solved.

The repair stories for this part are helpfull. The only problem I came accross was figuring out which part I needed to order. The parts diagram only showed one part labled 230, but when I used the drop down box to order the part there were 2 parts labled 230 for 2 diffrent prices. I called ge customer care and found out the less expencive part listed as 230 does not come with the wires etc. . The more expensive piece has the wire harness and every thing needed. I went with the more expensive part and it was a snap to install. . . .

Easy

Since the original part was a single element we had trouble locating the part we were replacing since it was replaced with a dual heater. Once located the repair went pretty well. We followed one of these wonderful postings that helped work through the difficulty.

removed the door hinge assembly & replaced it with the new assembly.

Not really sure of the age of this fridge, as we bought the house 2.5 yrs ago.

I'm one who if it can go wrong, it will, so not realizing how stable the door was from just having the top hinge and the magentic gasket, I declined to prop the door up on blocks the way some guys say the did, and instead removed the top hinge and lifted the whole door off the bottom hinge. I traced the outline of all parts with a felt pen before removing them, figuring I'd need witness marks to help with realignment after the install.
Nut driver might've been an easier choice than the socket set, but the only ones I have a brittle and I've broken the 5/16"...
All parts came out/off easily. The new bottom hinge and the old top hinge (both on the fridge side) practically aligned itself right on my marks, and the new cam (door side) just needed to be held while the screws were tightened. I used the extensioni rod off the ratchet to drive the screws most of the way (making a nutdriver out of it).
Parts were exactly as advertised, although there was a note in the package that stressed the need to replace both parts at the same time due to material differences in the original and replacement parts. Since the cam is sold separately without the hinge, it would be good for the website to reflect that before the purchase is made. Also, even though it was only the cam on the hinge and not the whole hinge that needed to be replaced, I could've bought hte two cams separately and drilled out the rivet as another person had done, but for the $5 difference in cost, why bother?
Door now closes itself as designed, albeit slower than the freezer side, but the Wife says it always did that.
Also interesting that when first assembled, the door DIDN'T close itself at first... not sure it it needed to wear a litle, or if it just needed the added weight of having items back in the door shelves.
Love the great website... just typed in the model number and the parts I needed, complete with drawings to make sure, were right there. Great UI.

I removed the top hinge, lifted the door off the bottom hinge, rmoved and replaced the bottom hinge assembly, and reinstalled the door. I then aligned the door and reinstalled the upper hinge. The fridge works just like new!

removed door, removed old cracked riser aand replaced with new. You have a easy to follow parts site and very good prices. I will use you for all my future repairs.

Cake walk repair.

Unload the door then close it.
Remove screw holding plastic cover over hinge on top.
Remove 2 bolts attaching the hinge on the door.
Slowly open and lift door off of bottom hinge lay on counter.
Unscrew bolt, insert new cam, tighten bolt ,set back on bottom hinge, center install top hinge, tighten and install cover. tool me 6 minutes.

After recieving the part overnight (Very unexpected speedy delivery!) I propped the freezer side door up with a 4x4 and 2x4 and the old part came right off and the new part went right on with no hassels, Done in less than 15 min!!!!
The new part even came with step by step easy to follow directions.