TBX25PRBSRCC General Electric Refrigerator - Instructions

Removed icemaker from freezer,
Removed 3 screws from cover plate, and removed screw securing main gear, removed gear.
Pulled back cover plate to expose switches and mechanism.
Removed screw holding switch to remove switch, and installed new switch.
I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install.
But it works!

Took out shelf & brackets. Removed plastic shelf. Unscrewed broken bracket & screwed in new bracket.
Put back in & replaced the shelf.

Removed drawers and glass shelf. Removed screws that hold old slide rails in place. Installed new rails and re-installed cover for vents. Placed assembly back in and installed drawers.

I followed the directions on the site for the center slide replacement. I had actually called a local store and had him order the first part. It took several days and then I started searching online and found this site.Then I ordered the second part on line and to my surprise it arrived the next day. I was fortunate enough to have lived only about 70 miles from the distributer.Following the directions I found here is how I attempted the initial repair. With the vegetable bins out fo the bottom, I removed the plate covering the front frame by gently prying it off. Then I removed the two screws to losen the bar and lifted out the glass shelf. I didn't have much difficulty removing the frame since the front piece support for the slide rail that fit into the frame was already broken. I also had to loosen the screws on the back rail. I removed the entire frame and then replaced the side rail reinserting it into the end caps. I replaced the back screws and then the front ones .I replaced the glass shelf and then the cover cap for the shelf.
The only problem I encountered was that I couldn't seem to get the back screws really tight and I don't know why.

Screwed new bulb in socket

removed produce drawers, removed center piece front cover, removed glass shelf, removed broken drawer slide rail - unscrewing where attached in the rear of the refrigerator. Also removed screw from centerpiece where broken drawer slide rail was attached. reassembled all very quickly....saved myself having to buy another refrigerator by doing this simple repair.

Unscrewed four screws, two on each part, and replaced broken parts, reinserting screws. This is a no-brainer repair.

Basically I removed 4 screws holding the rails together, did a little cleaning of the existing parts that I would re-use and screwed the 4 screws back in and put it back into the fridge. Piece of cake. If I hadn't cleaned up the old parts it would have taken me 5 minutes.

I pulled out the shelf and removed the 2 screws holding the broken side rail to the shelf frame. I then screwed the new rail in and set the shelf back in.

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flapper connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.

Ordered part came in 3 days. Removed plug and rear cover. Pulled off old fan . Installed new fan by pushing it on to shaft. Plugged unit back in to check operation, installed rear cover. Done. Part fit perfect. Thanks to this site you folks are great !

Remove old gasket by pulling out one corner at a time and Installing it by placing it in the grove.

Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.

There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great