GSS22IBMACC General Electric Refrigerator - Instructions

I must admit - I thought I'd attempt to do this repair and end up calling a service guy to finish it. I'm not mechanically inclined AT ALL but thought I'd give it a shot after reading others experiences. I'm glad I did. The fix was easy, but there was initial anxiety while reading the instructions that came with the part - as they mentioned the possible need to cut some wires. Fortunately that was not necessary..... Removed three screws from the rear plate to expose the part needing to be replaced. Remove the fittings from the old board (needed plyers to do that - be gentle), take the old board out by using needle nose pliers to squeeze the white plastic tabs and pull the board free. Reconnect fittings to new board and you are done. Works better now than ever - obviously the old board had an issue that GE should have recalled, as many others had the same problem.

Pulled out the fridge and unplugged electric cord. Took off the back lower right side panel. Unplugged all the connectors and removed the motherboard. Replaced the motherboard and reconnected connectors. Replaced the panel and plugged it in. Works great!

1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

exchanged

The original design is poor. The evaporator fan is mounted in an upright position just below the ice-maker. A plastic grate mounts over the fan assembly to allow for air circulation. Unfortunately, random chips of ice from the ice maker can fall into the fan, causing the fan to shear its blades. Replacement of the fan blade is relatively simple (accept for having to completely unload the freezer and remove all back covers, the ice-maker auger motor assembly, and the metal evaporator cover). In order to mimimze this from reoccuring, I installed a 1/4'' mesh metal screen over the exhaust ports on the cover. Thus far, this has worked well to keep ice chips out of the evaporator fan.

Turned the power of to the fridge took the food out of the freezer put in the fridge took out all the shelves and took off the panel to get to the coils. I used a hair dryer and a shop vac to defrost the coils used the shop vac to suck up the water as the ice melted also put some paper towel in the drip tube so the water would not go to the drip pan. Took off old defrost heater which was a single heater the new on was a double heater fished out the blue wire from the left side of compartment and ran it down the right side plugged both wires into the heater mounted it into place and put everything back. Turned on fridge and it has been working fine ever since. Thanks for the last person that did this I read his review and it really was that easy
Thanks Jerry

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

Unplugged unit.. Removed control board cover.. Removed all plugs from control board then removed board its self.. Replaced in reverse order.. Unit is working as new..

Great Service! Received the part the NEXT DAY!

We originally called a service technician. He came the next day and said the mother board was no good. He order a new one and replaced it a week later. Total part & labor cost: $185.00 (Remember we're without a working refrigerator the whole time the part is on order)
Two days later the freezer is doing the same thing. We call the tech again and he seems confused and says it could be the heating element, he'll order one at no charge and replace it for us free. He never comes back with the part and does not answer our 2 dozen phone calls. I checked the element myself and saw that the tube had been scorched, like a burnt out light bulb. Searched for parts on internet and found this great site. "Partselect.com"
REPAIR:
Refrigerator had been unplugged for a few days to defrost ice build up in freezer. First, I removed the shelves from freezer compartment, removed the back panel and removed screws holding heater element in place, I unplugged the two electrical leads and plugged in new part. AS EASY AS THAT !!!!! I reinstalled the screws to hold the element, installed the back panel and replaced the freezer shelves. I plugged the refrigerator back in and within hours the freezer started making ice again. It's been about 3 weeks and we have not had a problem since.
Fantastic Service and instructions and Inexpensive !!!! I will use this site again, if needed, and will recommemd to anyone who needs parts.

The back panel was unscrewed, we read the directions with the circuit board and followed them. It was very easy to unplug the old faulty unit and plug in the new replacement part. It was done in 4 minutes flat. Very easy to do yourselves!

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Unbolted the back cover, pulled out old board, replaced with new bored and powered back on. It is working great now.

First, I removed the cover plate from behind the fridge. Next, I carefully pulled the main board out (four little clips holding it in) and disconnected the plug in wires. I connected the wires to the new board, popped it back in place and replaced the cover. Very easy to do.

Simple directions were provided. It took more to clean and vaccuum than the actual repair. Yes I replaced the motherboard in a referigerator. Just keep not of the connectors and were they came off from on the original board. Dont just rip them off because the new board has some different connections. So follow the directions and take your time if your not sure. But really it a cinch. No more whoooo sheeesh and howling noises from the referigerator. Thank goodness.