TPG21JRYDBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jason from zion grove, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rubbeer flapper was worped causing frost in the freeze
The same as the vidio, very easy. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Franklin, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door recess asm would not seal tightly
remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from milford, CT
- Parts Used:
- WR30X256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken ice bucket
Very easy to repair-Went online-Found diagrahm-Ordered part-and presto it was fixed.
Very good schematic to go by. If you can read you most likely can fix it.
Very good schematic to go by. If you can read you most likely can fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THEOTIS from CHARLOTTE, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator COnstant running and low ice output
I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERIC from DAYTON, OH
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Frost on inside of freezer.
Since my refrig is 18 yrs. old and I never had to replace it, took a little long to remove trim piece on the outside. After that repair went smoothly. I still have problem with water collecting inside on the bottom of the freezer, might have a leak somewhere. Ice maker is functioning correctly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Bridgewater, NJ
- Parts Used:
- WR17X3089
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice dispenser had a transistor failure on the control board
The solenoid in the dispenser was overheated due to the control board failure. After I rerplaced the board I found the heat had distorted the plastic crank and jammed the solenoid action. The plastic crank was easy to replace. Now after expending approx. $75 everything works normally!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Saint Johns, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Frost in ice dispensor
Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Denison, TX
- Parts Used:
- WR17X4341
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The ice auger was rusting getting rust on the ice cubes. This also hindered the auger from working properly.
I removed the ice container with the auger inside. I removed the front panel, then the auger and housing. I had to clean all of the parts that had rust on them. I got some of the parts mixed up and was having a hard time putting them back where they belonged. I went back on the PartSelect web site and with my IPad and opened the exploded view of the parts. This enabled me to put the auger back together. It works perfectly now. Saved a lot of money by doing it myself. Thanks PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Mooresville, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Dispenser Door Seal not sealing, frost in freezer
Googled how to replace the door seal, ordered parts and replaced the door seal flapper. The video on partselect was not correct for this GE model. However a simple diagran showed you simply remove the control panel directly (pops off) to provide access to the panel. Remove the 4 screws holding the panel, replace the door seal, and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Austin, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heavy frost was forming where ice is dispensed
Watched the PartSelect video. Very simple and solved the problem. Very pleased with the repair and PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Houston, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice flapper replacement in freezer door
Looked at the instructional video and read previous customer comments. Didn't have to dissassemble rear of freezer door. Access through the front once trim ring and circuit board removed. Could not have done it with out the video/and or previous customer comments. Part was shipped and received immediately. Repairs complete! No more frost developing and plugging ice chute! I especially appreciate the customer comments on how to complete this repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Concord, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost in and around ice maker outlet
Followed the video directions. Spent about 5 minutes and I was done. Very easy to do. Problem with frost is gone. The video makes it easy to remove the plastic parts without any damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from Grand Blanc, MI
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
We had ice crystals on the ice tray and door
Removed the ice maker control panel and accessed the flapper door, easy switch out for new door and seal. The 2 year old warped seal didn't close and so ice crystals formed in the freezer - new unwarped part and Ta-Da no more problems :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Little Elm, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost buildup in the freezer near the ice chute.
I watched the video on the PartSelect.com website and decided to give it a try. The replacement of the flapper was even easier than I anticipated! The old flapper was extremely warped and was allowing air into the freezer. I'm not sure how/why it was in that condition but I am happy to report that I have no more ice buildup. Thank you, PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Nags Head, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
flapper was locking open periodically.
Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the interior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!
Was this instruction helpful to you?
Thank you for voting!