TPX24BPDBWW General Electric Refrigerator - Instructions

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.

1. Turned off the water supply to the refrigerator.
2. Removed the front panel and disconnected the water line to the front left.
3. Removed the left rear (freezer side) panel and disconnected the reservoir from the main water supply input. This was a little tricky to figure out. You must push in the water line at the same time pushing in the coupling. Then pull the line out while keeping the coupling pressed in.
4. Removed the screw that holds the reservoir to the back of the refrigerator.
5. Pulled the old reservoir out and replaced it with the new one.
6. Basically the rest is the reverse of the above. It took a little bit to fish the lines through the original path they came.

Overall this was an easy repair. If I had known how the coupling in step 3 worked this would have been a 15-minute project.

I started by shutting off the water inlet valve and then unplugged the refrgerator. I then disconnected the tubing leading into the solnoid. Removed the old solenoid, replaced it with the new part reconnectted the tubing and gave it a test run. After about 2 hours we had ice being made again! I then reconnected the bracket to the refrigerator and haven't had a problem since.

I removed the cover on the back of the freezer side of refrigerator to expose the anti freeze element use the hair blow dryer to melt the ice on the coils put 2 towels to colect the water thats wath take me time, to replace the heath element was a 1 minute job.

First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic door jamb putting the new unit in but other than that all is well and functioning well.

Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.

Disassembled ice-maker, noting what screws went where, what direction ice release control arm pointed, and noting how the control arm spring was mounted. The door assembly comes off first followed by the circular assembly that houses the ice door and last grinding arms. It is quite easy see how it comes apart as you look at the screws. Remove the screw holding the back end of the control arm and note the spring position. The control arm needs to be turned to line up notches to pull it thru a faceplate hole while rotating the arm about the "U" that is on the outside of the faceplate in the door housing. There is a retaining clip holding the rotating impeller to remove to complete the dis-assembly. Use vinegar to clean rust out of bin and other parts around the faceplate. Assemble the unit in the reverse order to complete the job.

Let me start by saying, I usually hire something like this out but figured I would give it a try. The install was fairly straight forward, however it would’ve been nice if the instructions would have been more useful. Instructing me to remove one screw to release the auger and solenoid enclosure wouldve been nice. There were 3 other screws that I didn’t need to remove and they were the ones holding the auger in place, which made assembling that much more difficult. Once to enclosure was removed, and the solenoid was exposed, it was a seemless process. I would however, recommend paying attention to or taking a picture of the connections on the solenoid. I was lucky to remember or got lucky. Regardless, I was able to complete the project successfully. If I had to do it again, I believe it can be done in 30 minutes or less.

The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. Once we had access to the flapper, it was easy to replace it. The repair fixed the problem.

I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.

Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.

Defrost heater turned black. Test showed infinite resistance. Problem went away after the heater was replaced.

Grill for the water dispenser in the door. All I had to do was drop the new one in place.

Received the new grill in one day after ordering.

First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.

------------- defrost heater replacement --------------------------
- unplug the refrigerator
- unload all shelves underneath ice maker
- move ice crem into the refrigerator section
- remove all shelves and the bottom tray.
- remove light bulb cover and the bulb
- unscrew two 1/8" screws on top corners of the back panel
- unclip the ground clip on top
- pull the back panel up; pull the left side toward yourself
- test 3 thermistors (see instructions below)
- test the thermostat (see instructions below)
- if either thermistors or the thermostat units are defective, they may be the reason for fan malfunction, not the fan itself.
- unscrew 2 philips screws on either side of the defrost heater
- pull it out and unplug the 2 wires on either end. Replace with a new part.
- putting together is the reverse of disassembly
- move ice cream back to the freezer


--- thermistor testing

- unplug the refrigerator
- locate thermistors to be tested. There's one on evaporating coils, one on bot. left of the freezer (behind deep tray, with white wires), 1 in fridge section (top left, in the corner, inside square white wire conduit; undo the top 1/8" screw ONLY and pull conduit up).
- without disconnecting from the circuit, place a thermistor in a cup of ice water. Wait for 5 minutes
- locate the main control board. Locate and unplug the J1 connector. The pinout, starting from the side with all wires connected:
* pin 5: ground
* pin 4: evaporator thermistor
* pin 3: freezer
* pins 2,1: fresh food thermistor
- use an ohmmeter to measure resistance. Push the needle of the ohmmeter into the socket, where the wire plugs in, without trying to remove the wire. It should be 16.3 kOhm +/- 5% (for 0 deg C)

to replace a thermistor
- cut out the old thermistor, leaving as much wire as possible
- strip the wires, twist them pairwise
- use a bell connector filled with RTV silicone, to ensure that no moisture can get to the connection
* others have also used butt splices and screw-on caps with electrical tape (for moisture isolation)
- using a proper crimping tool, squeeze the bell connector to secure the wire

------------- thermostat testing ---------------------------------
- it's a round quarter-sized cylinder w/ pink and orange wires
- check for bulging (= burnt)
- locate temperature ratings on the side of the thermostat. It should read e.g. 140-30F. This means it's switches to open circuit when >140F is reached and switches to closed circuit when <30F is reached.
- unplue the 6 pin connector that has thermostat.
- test the thermostat. Orange wire is in the 6-pin connector; pink wire can be disconnected from the defrost heater under the evaporation coil. It should read closed circuit (no R).
- place the thermostat into a cup of boiling water. It should open.
- if OK, reattach the thermostat