TFG25JRYDWW General Electric Refrigerator - Instructions

The hardest part was getting hte right replacement drawer.

Easy to take apart just keep track of all your screws and parts most inportant of all are the 3 claw like and spacers that are inside the clear round part at the end of the ice bucket these pieces only turn in one direction if you put them on backwards or in the wrong order you will tear up your ice bucket so pay close attention when taking it apart and reassembling it. One think that might be helpful is to take some pictures of the ice bucket before disassembly something i wish i had done prior to taking it apart. Some people download instructions off the internet but i felt like i could do it with out help well good luck

Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.

Put the cover in place.

I followed the Video on your website and that made it so easy and simple to follow. Thank you!

Remove ice maker bucket. Unscrew single screw in center of shield, take out shield. Insert new shield, making sure the 2 tabs on the shield are slid into mount from the left, center the shield so center tab is aligned with screw hole, Tighten screw, replace ice bucket. SUGGESTION: This would be a good time to replace light bulb!

Pull out old pan,remove the vent cover from front and install it on the new pan, done.

Since my refrig is 18 yrs. old and I never had to replace it, took a little long to remove trim piece on the outside. After that repair went smoothly. I still have problem with water collecting inside on the bottom of the freezer, might have a leak somewhere. Ice maker is functioning correctly.

The solenoid in the dispenser was overheated due to the control board failure. After I rerplaced the board I found the heat had distorted the plastic crank and jammed the solenoid action. The plastic crank was easy to replace. Now after expending approx. $75 everything works normally!

pulled fridge away from wall, shut water to fridge disconnected both lines,back one and front one.Removed old water resevoir 1 screw. cut old lines at resevoir. used small threaded rod (1"long)to connect old lines to new lines and taped together,pulled new lines with old lines and reconnected.No lifting of fridge,actual repair under 1 Hour but took longer because I cleaned underneath really well and took my time.

Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.

I removed the ice container with the auger inside. I removed the front panel, then the auger and housing. I had to clean all of the parts that had rust on them. I got some of the parts mixed up and was having a hard time putting them back where they belonged. I went back on the PartSelect web site and with my IPad and opened the exploded view of the parts. This enabled me to put the auger back together. It works perfectly now. Saved a lot of money by doing it myself. Thanks PartSelect.

I had read from your sight, to simply cut the lines at the reservoir and tape the new lines to the old. Then use the old lines to pull/feed the new lines to the coupler/valve. This worked great and greatly decreased the time it took to install. I spent more time moving out the frig and cleaning up all the dust (probably should do that more often)

Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the interior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!

Googled how to replace the door seal, ordered parts and replaced the door seal flapper. The video on partselect was not correct for this GE model. However a simple diagran showed you simply remove the control panel directly (pops off) to provide access to the panel. Remove the 4 screws holding the panel, replace the door seal, and reassemble.