MSK28DHZCWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jorge from Clarksburg, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Ice flapper warped.
The Ice flapper was warped therefore, it was not closing well. Because of this, the ice dispenser got air in it and the ice cubes would deice causing to make a chunk of ice inside.I went on line, order the part ($5.75 + tax= $12.00) checked Part Select video and did it myself. It really is as seen on the video. It took me less than 10 minutes! I saved $200.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Pasadena, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice/Water dispenser freezing/clogging
I followed the Video on your website and that made it so easy and simple to follow. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Dumfries, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper valve allowing frost/ice to accumulate in chute in summer
Followed the online video exactly and it was easily done. Couldn't have been better. The problem is solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Kennesaw, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice dispense door flapper was deformed letting warm air into the freezer compartment.
The trim piece covering the opening of the dispenser is the first and most difficult part of the disassembly. Take care when removing this piece that it does not break.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Glendora, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inside freeze was frosting up
used a flat screwdriver to pop off out side cover then remove 6 screws took off plate. Pulled off the flapper and replaced. less the 15 mins and fixed the issue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Austin, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heavy frost was forming where ice is dispensed
Watched the PartSelect video. Very simple and solved the problem. Very pleased with the repair and PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Hughesville, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice dispenser chute kept freezing with condensation
The flapper on the ice chute was curled up and not creating a good seat, so the chute kept clogging up with frozen condensation, especially during the humid summer months. The online video made it so easy to replace the part myself. I was able to fix the problem in under 15 minutes and at a fraction of the price!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Chester Springs, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper was warpped
Follow instruction on the video you provided
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GWEN H from CONCORD, CA
- Parts Used:
- WR32X1492
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Upper Vegetable Pan
The hardest part was getting hte right replacement drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andy from clearwater, FL
- Parts Used:
- WR32X1492
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pan right edge is broken
Pull out old pan,remove the vent cover from front and install it on the new pan, done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Fripp island, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
3rd Flap for this Ice Mkaer, keeps warping
Very Easy, follow direction I the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Pittsboro, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The flapper on the freezer was warped and allowed humidity to create frost in the freezer.
I watched the how to video and followed the instructions. The entire repair took less than 4 minutes. Hardest thing was disconnecting the control panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THEOTIS from CHARLOTTE, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator COnstant running and low ice output
I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Nags Head, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
flapper was locking open periodically.
Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the interior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERIC from DAYTON, OH
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Frost on inside of freezer.
Since my refrig is 18 yrs. old and I never had to replace it, took a little long to remove trim piece on the outside. After that repair went smoothly. I still have problem with water collecting inside on the bottom of the freezer, might have a leak somewhere. Ice maker is functioning correctly.
Was this instruction helpful to you?
Thank you for voting!