TBX22PRBMRBB General Electric Refrigerator - Instructions

I followed the directions on the site for the center slide replacement. I had actually called a local store and had him order the first part. It took several days and then I started searching online and found this site.Then I ordered the second part on line and to my surprise it arrived the next day. I was fortunate enough to have lived only about 70 miles from the distributer.Following the directions I found here is how I attempted the initial repair. With the vegetable bins out fo the bottom, I removed the plate covering the front frame by gently prying it off. Then I removed the two screws to losen the bar and lifted out the glass shelf. I didn't have much difficulty removing the frame since the front piece support for the slide rail that fit into the frame was already broken. I also had to loosen the screws on the back rail. I removed the entire frame and then replaced the side rail reinserting it into the end caps. I replaced the back screws and then the front ones .I replaced the glass shelf and then the cover cap for the shelf.
The only problem I encountered was that I couldn't seem to get the back screws really tight and I don't know why.

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together

Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.

I had to remove the glass shelve, the two drawers, and the middle rail. Once I did that, I slide the unit out together. I placed the unit on the floor and removed the one screw located on the far backside of the unit. I had to remove a slip cover (it had the kenmore logo and the writting on it) it was a snap on, so no problem. Glad it was not gluded on. After the old part was removed, I put the new part on. Put the two screws back on and snap the cover back on. Then I put the whole unit back in. This included the glassshelve and drawers. The process was pretty easy. Good luck with your change.

Took out both draws and glass shelf, removed the entire lower shelf housing. I snapped off the front rail aluminum face to expose the screw. Unscrewed both screws and removed the rail and then just reversed the procedure to put new rail on. It was the most cost effective way of doing it. All the pieces are there on the GE website as long as you know the model number. You will save a lot of money by doing it yourself.

Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flapper connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.

Unscrewed four screws, two on each part, and replaced broken parts, reinserting screws. This is a no-brainer repair.

Basically I removed 4 screws holding the rails together, did a little cleaning of the existing parts that I would re-use and screwed the 4 screws back in and put it back into the fridge. Piece of cake. If I hadn't cleaned up the old parts it would have taken me 5 minutes.

removed produce drawers, removed center piece front cover, removed glass shelf, removed broken drawer slide rail - unscrewing where attached in the rear of the refrigerator. Also removed screw from centerpiece where broken drawer slide rail was attached. reassembled all very quickly....saved myself having to buy another refrigerator by doing this simple repair.

I pulled out the shelf and removed the 2 screws holding the broken side rail to the shelf frame. I then screwed the new rail in and set the shelf back in.

Screwed new bulb in socket

I just followed the instructions on the video and it was exactly as they said......no surprises.

removed the bulb from the package unscrewed the old bulb & screwed in the new bulb.

Remove the burned out bulb and install the new light bulb.