TFG22JABEWW General Electric Refrigerator - Instructions

Cake walk repair.

Unload the door then close it.
Remove screw holding plastic cover over hinge on top.
Remove 2 bolts attaching the hinge on the door.
Slowly open and lift door off of bottom hinge lay on counter.
Unscrew bolt, insert new cam, tighten bolt ,set back on bottom hinge, center install top hinge, tighten and install cover. tool me 6 minutes.

removed door, removed old cracked riser aand replaced with new. You have a easy to follow parts site and very good prices. I will use you for all my future repairs.

Remove the hinge cap on top, the loosen the bolts, remove the hinge. Pick up the door from the lower hinge, lay it down and place the cam riser on the lower hinge. Replace the door, install the top hinge and check the alignment and you are done.

Super simple! Hardest part of the entire process was identifying which part I needed to order. Once I received the part (which shipped promptly and was at my front door within 2 days), all it took was 5 mins and a screwdriver and I was back to having a usable snack drawer!

Emptied the refrigerator door so it was easier to take off. Used a screwdriver to remove the screw on the top hinge. Lifted door off bottom hinge. Laid the door down so I could take the bottom hinge off. Removed worn out parts and placed the new one on. Slipped door back on hinge,made sure it would close properly and was lined up with freeze door. Put top hinge back in place. Done!! Now door finally shuts on its own again!!! EASY!!!

remove plastic top hinge cover then twoscrews holding door with door closed it rested against freezer door then lefted off door put on flat surface remove tow screws at bottom of door installed new cam

Just watch the Parts Select YouTube videos on replacing the door hinges. That helped a lot.

All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.

My job pretty much paralled the no. one on this list,I am a retired industrial electrician and have many years experience doing similar jobs.Went very well. . Tom Pennington of Muncie Indiana

This door was a problem for 1-2 years before I realized it had dropped about 2 inches. On close examination I saw that the hinge parts had completely broke down.
Had original manual-looked up model # on line under GE appliance and was surprised to find a large complete parts dwg showing parts I needed. Decided I needed the hinge assy.
Removed the door cap on top,replaced hinge assy and remounted door in reverse.--Works like new.

Followed other messages to complete fix. Simple overall.

Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.

Lifted the door while closed into position even with freezer door. Then put srap pieces of wood under door to hold into place while I removed the old hinge assembly and replaced with the new one. The door works good now. Make sure you replace both peices as they will both be worn.

Turned refrigerator off. Removed food from right hand (refig.) door. Closed door. Removed upper hinge cover with a standard Phillips screwdriver and then removed upper hinge by removing two 5/16" bolts using nutdriver. Lifted door up to clear the bottom hinge-post and set it on the table. Removed the kick pan at the bottom of the refrigerator and then removed the bottom hinge-post which was attached with two more 5/16" bolts. Installed new lower hinge post and rubbed a small amount of mineral oil on the closing cam (which is riveted to the hinge-post). Removed the old upper closing cam from the door (5/16" bolts) while it as lying horizontal on the table and installed new cam lubricated with a small amount of mineral oil. dropped the door in place, replaced upper hinge and cover. Replaced kick pan. Done.

Removed all items from the door shelfs.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now level with the freezer door.

I had to remove the top hinge of the door and shut off the water supply to the automatic ice maker. I then unhooked the water line and pulled it through the guide as I took the door off. Once the door was off, I removed one bolt with the nut driver and replaced the cam. I reversed the above actions and replaced the door. It is very important to adjust the door so the seal fits tightly and evenly all round the door. It was a relatively simple procedure that went very smoothly.

Just remove all items in door shelves, remove screw holding top hinge cover on. Remove two bolts holding top hinge and remove hinge from door. Carefully open door and lift out of bottom hinge. Remove screw holding bottom hinge on door and replace broking cam riser. Reinstall door in reverse order and adjust top hinge where both doors are even across the top. Thats it!!!!!