TFF24SCB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from HAZELHURST, WI
- Parts Used:
- 7C7
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light bulb in my freezer door burned out.
Remove the burned out bulb and install the new light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Salinas, CA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Door closing cam split in two and door would not automatically close anymore.
This one is a no brainer… One Phillips screw on top to pull top door hinge trim. Two nuts and the top hinge is free. Then pull the door… it helps if you unload all the crap in the door bins. Remove the remnants of the door cam and that leaves a pop rivet. Put some vise grips on the head and use a hacksaw to remove the lower part of the rivet. Then pop-rivet the new door cam in place. If you don’t own a pop-rivet tool, I guess you could use a 10/32” screw and nylock. Plop the door back on and you’re done. Took all of about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Raleigh, NC
- Parts Used:
- WR72X206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken drawer slide
Removed 2 screws to remove broken slide, replaced 2 screws with new slide. Took every bit of 4 min. to complete job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from Columbus, OH
- Parts Used:
- WR72X207
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Rail
After fixing my washer this was a snap. After lifting out drawer and shelf only two screws needed removal. I think it was easier putting it back together! It is sites like these that make it possible for men to feel like men!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from DENVER, CO
- Parts Used:
- 7C7
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drum light burned out
removed the bulb from the package unscrewed the old bulb & screwed in the new bulb.
Was this instruction helpful to you?
Thank you for voting!
broken drawer guides in rental refridgerator
Piece of cake, unscrewed two screws on each drawer guide and simply relaced the new sides. Fit was perfect and fridge is like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- derryl from ALAMOGORDO, NM
- Parts Used:
- WR72X207
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace Broken Drawer Slide
Remove glass shelf. Remove slide (2 screws). Replace with new slide. Replace glass shelf. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmie from Surprise, AZ
- Parts Used:
- 7C7
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb burned out.
Screwed new bulb in socket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- C. Robert from Sandusky, OH
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door closer cam riser
I blocked the door up with one 2X4 Then removed the lower hinge, installed the closing cam. Then I found that I needed one more closing cam that I didn't order the first time. This other one mounts to the lower section of the door and both cams set together. Re-ordered another cam. When it came in I installed it. Between ordering both parts I had them both in three days. The best to Parts Select
I now know where to buy my parts if needed again.
Thanks
Bob
Sandusky, Ohio
I now know where to buy my parts if needed again.
Thanks
Bob
Sandusky, Ohio
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERIC from EL DORADO HILLS, CA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
door would not shut
Like the rest of the other statements it was easy with 2 2X4 pieces of wood to block the door up. The other suggestion about buying two of the pieces was a good idea. Once I took off both the top and bottom pieces they were both worn out and it was easy to replace them both at the same time. The door is working good again and shuts on its own.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLen from Greenfield Twp, PA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken door cam will not close on its own
First i removed the lower cover below doors . Then placed a 4x4 under the door to be fixed to keep it in place. Removed screws from hinge support on unit to remove cam Removed outside screw on door and loosened other to allow other cam to be removed . Always buy two cams if one is broken the other cant be in very good shape .The door will work like new with two .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Dallas, TX
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken cam pieces, top and bottom
Removed the top hinge cover held by one screw. Removed the top hinge held by two screws and them lifted the door up and off the bottom hinge. Laid the door on the floor and replaced the cam piece from the kit on the bottome of the door. That required removing one screw and losening another. Removed the lower hinge (two screws) and replaced it with the new one in the kit. The lower hinge includes the other cam piece. Lifted the door onto the lower hinge and then replaced the top hinge and cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Concord, NC
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Bottom cam at bottom of door broken.
Read the how to's AFTER ordering the part. 2 things....1) I wish I had read the comments first and 2) it was much easier than the comments led me to believe.
Had I read the comments first, I would have known to order BOTH the upper and lower cam....though there not a problem with the operation of the door. It would just have been a tad better if I had both. I'm not wanting to have to pay shipping for an additional part when the door works satisfactorily as it is.
As to the comments on how to do it....I took none of them. I (instead) removed the top hinge, and lifted to door off. I did have to have assistance to get the hole in the door aligned with the post, but that was rather easily done.
Would I do it again.....in a heart beat. I feel that I've save on the repair man making a call at the house, and experience has had me charged $60-$100 for virtually the same amount of service. My cost...shipping and all was under $20.00
Had I read the comments first, I would have known to order BOTH the upper and lower cam....though there not a problem with the operation of the door. It would just have been a tad better if I had both. I'm not wanting to have to pay shipping for an additional part when the door works satisfactorily as it is.
As to the comments on how to do it....I took none of them. I (instead) removed the top hinge, and lifted to door off. I did have to have assistance to get the hole in the door aligned with the post, but that was rather easily done.
Would I do it again.....in a heart beat. I feel that I've save on the repair man making a call at the house, and experience has had me charged $60-$100 for virtually the same amount of service. My cost...shipping and all was under $20.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodger from Brunswick, OH
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door wouldn't close with out help.
Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.
Was this instruction helpful to you?
Thank you for voting!