TBX18SYYBRWH General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alfred from Hudson, NH
- Parts Used:
- WR32X10398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
draw slide broke off
removed broken crisper cover and replaced with new one put draws back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith M from Tucson, AZ
- Parts Used:
- WR32X10398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf above crisper drawers
Super easy, remove drawers, remove broken shelf, slide new shelf into slots and return crisper drawers to their new support system. Very speedy receipt of appliance part and it took about 5 minutes to make change. Thanks much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Newark, OH
- Parts Used:
- WR32X10398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper lid was cracked
Removed drawers put in new lid replaced drawers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MAE from FARMERS BRANCH, TX
- Parts Used:
- WR24X10236, WR24X10228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The old gaskets were not sealing properly.
removed the old gaskets with the putty knife to pry it loose then pulled the old gaskets off. Soaked the new gaskets in slightly boiling water to make them better able to straighten out and then installed by lining them up and pressing them in place, making sure they were lined up and that they were in the track provided for them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Brooklyn, NY
- Parts Used:
- WR32X10398
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
the Vegetable Drawer Cover was broke in several places
We removed the old Drawer Cover and replaced it with the new one. The Refrigerator Door had trouble closing. So we inserted the 2 plastic washers as described in the directions enclosed in the packaging. It was pretty straight forward and an easy fix. Thank you Hot Point and Part Select. Pete and Bonnie, Brooklyn NY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Daggett, MI
- Parts Used:
- WR32X10398
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
broken shelf
after simply replacing shelf, I used the enclosed plactic washers to raise the height of door, so it would clear new shelf. It all worked as planned, thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- r from Bronx, NY
- Parts Used:
- WR24X10236, WR24X10228
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Gaskets needed replacement to maintain correct temperature in the refrigerator and freezer
Removing the old gaskets was very simple. Replacing the fresh door gasket was the most time consuming. It would have been easier if I had help, it took a some time and patience. The gasket works perfectly. The freezer gasket was easy to replace. The gaskets fit perfectly, thank you. For the ladies out there, you if I can do it, so can you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- N Smith from Chicago, IL
- Parts Used:
- WR24X10236
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
replaced the refrigerator door gasket
The original gasket had ripped and the magnet strip was hanging out. Following information from several youtube video clips & suggestion from the seller, I soaked the gasket in a tub of hot water for 30min to make it more pliable. After removing the old gasket, I put on the new, which only appeared to just snap into a metal tract. However the door couldn't seal. There were big gaps. That is when I realized that the gasket was still rigid. So I took a heat gun and carefully blew hot air on the gasket as I pulled it out enough for the metal edge of the gasket to attach itself to the refrigerator. Took quite a while to get it to seal correctly, but seems to be working well now.
Was this instruction helpful to you?
Thank you for voting!