GSE23GGPFCWW General Electric Refrigerator - Instructions

Knew the switch was bad. Researched on the internet how to fix. Used a steak knife to pop the old one out, changed the contacts to the new switch and popped it back in. It took longer to open the box than it did to replace the switch. And the part arrived 2 days after I ordered it.

Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.

Cut old tubing in frig with wire cutters and pulled through the bottom wall and removed old tnak from the wall...Installed new tank and ran tubing down trough lower wall and connected to the valve and the freezer door.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. Once we had access to the flapper, it was easy to replace it. The repair fixed the problem.

Let me start by saying, I usually hire something like this out but figured I would give it a try. The install was fairly straight forward, however it would’ve been nice if the instructions would have been more useful. Instructing me to remove one screw to release the auger and solenoid enclosure wouldve been nice. There were 3 other screws that I didn’t need to remove and they were the ones holding the auger in place, which made assembling that much more difficult. Once to enclosure was removed, and the solenoid was exposed, it was a seemless process. I would however, recommend paying attention to or taking a picture of the connections on the solenoid. I was lucky to remember or got lucky. Regardless, I was able to complete the project successfully. If I had to do it again, I believe it can be done in 30 minutes or less.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

I watched the video a couple of times and followed the instructions exactly and the repair was very simple. This repair took me a bit more time than I thought it would just because I followed the steps methodically.

But the video was perfect to guide me through the procedure to replace this part. One of the longest parts was removing the shelving and food storage bins, cleaning them, drying them and then putting them back in after the tank was installed.

I thought this was my problem as this part causes 90% of the no water issue. However, replacing this part did not fix my problem. I suggest that you test the valve first by disconnecting the water feed from the filter and running the line into a bucket. Once disconnected press the water on the freezer door and see if water comes out.
Other than that, this part is easy to install. Take off the plastic in front of the filter, remover the retaining screws. Remove lower cover in back of the refrigerator, Remove 1 screw securing the valve, remove cover where tubes enter the refrigerator. Take off tubes from valve (be sure to note what is inlet and outlet) and feed back into refrigerator. Be sure to save the putty when the new one is installed.

In preparation, I removed the bottom crispers and shelf to clear space, and removed the hood and items above the tank near the light. You'll need to also move the fridge away from the wall to access the back. Installation seemed very easy - two screws holding the tank itself, one hose to the water supply in the back, and another to the bottom of the freezer door to dispense. Then the hard part started after it was installed. First, I could hear the click but no water was coming out. After several views of youtube videos, I realized there was a plug in the hose to the supply side. Duh! So now I had water, but also a slow drip when drawing water. I believe the issue was that I was not pushing the hose on firmly enough, and eventually I got it right. Also, you need to understand the connector: there is a little ring around the place the hose fits; pushing it TOWARD the housing releases the hose, and pulling it back AWAY locks the hose it place. That was not clear to me without watching a youtube video.

My wife did it in less than five minutes

Used the instruction provide by Part Select, which are easy to follow.
When it came to replacing the Solenoid, the two bottom screws were easy to remove, The third screw (located on the top) needed lo be loosened, That screw was very difficult to remove because it was rusted, and I had to replace it.
I suggest that a spare screw should be supplied wit the solenoid.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

I followed the instructions on a posted desctiption. It workded perfectly. Replacing the inner door panel was not as difficult as described. Just start the process with the screws in the middle of the door. Those two screw holes were not slots. All of the remaining screw holes had slots. I installed all of the door screws before tightening any. I workded right the first time.

Opened, discovered not flapper but more complicated