PFE28KBLSTS General Electric Refrigerator - Instructions

Replace fan . Fairly easy.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

Pulled the instructions up on U-tube and followed them. With the socket removed 5 small bolts. Took the old switches ( I replaced both switches being I had it apart), put the new switches in and then put the 5 bolts back in.

Once I received that New Part, just place the 1 Piece from the old Shelf into the New Part and mounted the Shelf in the Door.

It snapped in place.

I ended up ordering two valves, both of which were defective (bad) and would not pass water, for a total of $116.66. Then I had to get a service tech to install yet another valve (also a GE part) that was good and that fixed the problem (for another $187.00 charge). These parts seem to come from Canada or beyond so be careful if you order them as they too may be bad. I finally received a refund for one but I'm still hunting for a USA address to return the other one I need a refund for...good luck.

I didn’t open the part till I verified it was the same. Then I detached the assembly from the fridge and swapped the water lines individually. The metal bracket had gotten bent a little in shipment, but straightened easily and all went back together.

Replaced the water solenoid that has a filter/screen as part of the unit.
Removed the back bottom plate. Turned off water supply, removed hose from water valve. Removed valve assembly, and un-pluged wiring. Installed new unit reverse of removal

I diagnosed the sensors in my refrigerator by holding the sensor in and seeing if I could trick the sensor it partially worked. I then used a multimeter and did an ohm test on both sensors multiple times open and closed the switch to verify which switch failed because it worked a couple times but not always. It ended up being the switch on the left hand door with 3 terminals on it and after the replacement it has worked great for weeks now no issue. best 15 dollars and 25 minutes spent!

The overload protector was the problem. It plugs into the side of the compressor and the run capacitor plugs into it.

If you pull the overload protector and it rattles when you shake it, that's probably your diagnosis.

The replacement is different from the original and the wire connectors are different. Hold the thing in the same orientation as if it were plugged in. The vertical connector goes to the neutral wire, which on my fridge is orange. The horizontal connector is for the overload, which for mine is black and white. If you have a schematic you should verify the wires yourself.

Anyway, the refrigerator now works like new.

I determined one of the five LED lights in the refrigerator was dead by swapping it with a working one. The refrigerator lights are wired in series and if one of the lights is dead the remaining ones turn on, but very dim. I called PartSelect.com and thanks to their help we determined the correct part to order which is the oval-shaped cover LED assembly which includes the cover, LED, and female connector. The part from PartSelect arrived in three days. The oval-shape LED plastic Cover assembly is mounted on the refrigerator and held by a couple of side latches. First unplug the refrigerator and then proceed to lightly pry the oval-shaped cover side facing the rear of the refrigerator with your finger nail to remove it. With the LED cover removed you can then press on the LED connector tab to slide it off. Now slide the female connector of the replacement part to the refrigerator male connector and snap the oval-shape plastic cover onto the refrigerator receptacle and then plug it back to its outlet. Now all the lights in the refrigerator should light up brightly! That's all folks. Hope this helps. Good luck. Yours truly.

I recieved the package with the correct part number but the wrong part inside. The item in the package does not even resemble the part on the GE parts website. Tried to contact parts select but no luck.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

Locate the light that is completely out, remove the assembly. Unplug the wire harness in the back. Plug in the new assembly and snap into place in the cabinet.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.