GIE22JMNDRES General Electric Refrigerator - Instructions

watch the video very good

emptied the freezer compartment, unfastened the air column panel, then four small bolts to remove the back panel in the freezer, unplugged the motor, unscrewed the motor, installed all in te reverse order and had the compartment refilled and running again in less than a half hour.

Part came in a couple of days, very fast delivery. Read how other people installed. Only drawback was the youtube video was not available. Thanks again!

the hardest part for me was the fan blade clasp.still only took like 20 minutes.But the best part was, the part was delivered and fixed within 24 hours of buying online. Great service guy's, Thanks.

it was so easy to replace the part and good experience I love when I can trouble shoot and fix the problem

The is my 'refreshment' cooler and sits in our garage. Hotter than heck in the summer so the things runs a lot. Started making a little growling noise. Had to partially disassemble the back panel to get to the fan. Touched the exposed shaft for a second and the sound stopped. OK, it's the fan. Went on line, used the (really great) exploded diagram to figure out what I needed. A couple days later the parts show up. Installed the new fan blade and retainer Removed the old motor (couple of mounting screws), connected the new motor (a plug in) and mounted the new motor making sure the grommet on the front and back were engaged. Turned the unit on and everything worked. Reinstalled the foam channel, the back panel and it ran perfectly. Great support (the diagram), fast delivery and fair pricing. Not bad!

Removed all the freezer inside panels to inspect the motor before I ordered the part. It looked like a relatively easy job to change it. I also watched the really nice video on the website that re-inforced my confidence in doing the job. The part came in a few days. I disassembled the freezer interior exactly as the video showed.(Warning: be careful with the styrofoam piece if the fridge is not fully defrosted. The ice build-up could cause it to break when trying to pull it out!)The only problem I had was getting the little collar on and off the motor fan shaft, and getting the fan off the shaft. I had to pull really hard for it to come loose and then I had to push really hard to get it back on the new motor shaft. I didn't know if could have used any kind of lubricant or not, so I didn't. After that the re-assembly inside the freezer went well, being careful to put everything back in the correct order and position. Started the fridge back up and it has been running very quietly ever since. But, most important, my wife was impressed with my work and is very pleased with the result!

First I looked at the video on changing out the fan.Made a lot of difference. Everything was covered and made it simple. Wish I had gotten two grommets but the back one was in good shape and worked fine. My hearing isn't great but now I can't even hear the thing run unless the freezer door is open. The shipping was great! You sent it out immediately and in a few days it was here.

I simply followed the online video instructions.made the job easy and fun.

I followed the video instructions and the job was done in no time at all

Followed the video by Parts select. Very accurate to remove and replace. The only trouble I ran into was getting the clip back onto the fan blade shaft! Have to improvise and use a wirenut to spread it and it went right onto the shaft. Now working perfectly! Thanks for the video and the fast part service shipping...

Ordered the part and within three working days the part was delivered. It took two minutes to pry off the broken part and one minute to snap in the new one.

replaced with new one

It really was as simple as the other folks noted. Slid a screwdriver into the edge of the broken switch and it popped right out. Disconnected and reconnected each of the two wires and just slid the switch back into the slot. Truly a DIY fix.

Used screw driver to lightly remove the old switch. Disconnected the 2 electrical leads to the old switch, then I connected those leads to the new switch. The light immediately came back on and I placed the switch into its housing hole and popped it in place. It works perfectly now. My wife said "let there be light"! Very easy installation. Thanks.