TFX25PRBBWW General Electric Refrigerator - Instructions

Followed the video on the computer. Was fixed in no time. Works great.

There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great

Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flapper connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

Emptied refrigerator door shelves. Supported door with 4x4 blocks. Removed old door hinge and replaced with new door hinge and cams. Pleased with end result and dealing with PartSelect.

I unloaded the door and took the cover off at the top of the upper hinge (1 phillips screw) I then unbolted the upper hinge (2-28mm bolts) and lifted the door off. I was surprised how light it was. I laid the door down and installed the new cam riser on the door. I then unbolted the lower hinge (2-28mm bolts)and installed the new hinge.
I lubed the 2 hinges with vaseline and put the door back on the lower hinge. I then reinstalled the upper hinge and cover. It took about 15 minutes, and a lot of that was cleaning up. Oh yes, to get at the lower hinge you have to pull off the lower grate that covers the coils. It just snaps off and on. It was a very easy job.

Remove the burned out bulb and install the new light bulb.

replaced the broken one with the new part

I just followed the instructions on the video and it was exactly as they said......no surprises.

Just take out the old ones, and clip in the new ones

Concerned about removing and attaching front panel to broken drawer. Rep. said wasn't sure but most just snapped together. Rep. was correct. No tools required.

Easy repair. No need to remove the door. Simply prop up the door with blocks or books - remove hinge and riser assembly - replace with new parts. Total repair time about 15 minutes. Tools needed only an open end wrench.

Screwed new bulb in socket

ordered drawer face - perfect part- snapped right in. done. order came within 10 days.
will order again if needed.

First I pulled the door up to the top hinge and propped it up with phone books. Secondly I used a nutdriver with an 8mm attachment and removed the bottom hinge. Thirdly, I removed one screw from the bottom of the door with a socket and 8mm attachment and removed the broken cam riser. Being careful as to take note of how the cam was positioned. I then attached the new cam riser to the bottom of the door, attached the bottom hinge to the refrigerator, making sure the pieces (cam riser and plastic on bottom hinge) matched up and after everything was tight, removed the phone books. Remember to first remove the vent on the bottom of the refrigerator and it is much easier to maneuver the door if you empty the contents on the inside. Very easy, I am not very mechanically inclined and this is the first job that I finished in the amount of time as stated. Also, do not chance just the riser as both pieces will be worn. Hinge assembly comes with all you will need.