PDS22MBPABB General Electric Refrigerator - Instructions

removed cover from rear of refrigerator. disconnect mother board connections. Unplug first, used needle nose pliers to squeeze plastic tabs holding on motherboard and replaced old with new and plugged back in connections. Plug back in refrigerator and done.

the new board was more complicated than the old, however the install instructions seem to have anticipated this. It works for mow. thanks for inquiring'

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Easy

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

Very simple fix by replacing the mother board. Your "how to" video made the repair even easier. The appliance repair estimate was over $400. I saved over $200. I already recommended your site to several other people. Thanks for making it so easy

I easily removed the screws and then removed the board and took a picture so I would remember how to re-connect it. It was really easy and now my refrigerator is working great. If I can do it anyone can do it. My husband was amazed that I did it all by myself.

Moved fridge out from wall. Unplugged. Removed circuitboard cover 6 screws?). Replaced circuit board (showed burn spots on back side). Replaced cover and plugged back in.

I pulled the fridge out away from the wall, unplugged fridge, and found the panel that the main control board was behind. after comparing old board with the new i unpluged all of the connections unscrewed four screws and installed new board in reverse order. very simple..

Used 1/4 nut driver and drill to take off acc pnl. The repair amounted to unplugging several connectors, removing the old motherboard, installing the new board and reconnecting the wires. this solved the problem and the whole appliance seems to run better.

I read other reviews then decided it was my main control board.Watched the video for install. It was easy to change out.Everything is working great again.

read on line that fan control in main board can cause erratic running of the fan causing "whooing" and ghostly sounds. New board installed and now I have the quietest fridge in the neighborhood. Here's the unbelieveable part. Ordered the part online from parts select on good friday morning. Fed ex delivered it just after lunch the next day (saturday). Now that's the best service I've ever received!!

very easy repair, simple exchange

I checked the problems others were having to see if they had simular ones. They were having the same clicking noise I was having. My refrigerator would not turn on. Clicking noise but would not start. They replaced the motherboard. I searched the internet for prices. Part select was about $30.00 cheaper that the other stores. I ordered from part select. Nice helpful people to deal with. I installed the part in about 5 minutes, very easy repair. They sent me an updated part. Thanks everybody and Part Select for your help.

Ice & Water dispenser did not dispense. When pushing on the dispenser lever, the entire unit briefly lost power and reset as though the appliance was unplugged. I heard a click from the back of the unit where the main board was located.
Fridge made ice but didn't operate. I determined the micro-switch and solenoid were working properly. So the only thing that could be wrong was the board.
Removed main board panel with screw/nut driver. Unplugged board connections. Un-snapped main board from housing assembly. Installation is the reverse.
Very easy. Only needed was a screw/nut driver. Electrical connections are easy since the harnesses can only fit to their own connection. No way to make a mistake.
Took no more than 10 minutes.

Problem solved!