TFE27RRAWH General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- craig from sweeny, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
no water to ice maker or water dispencer
replaced circuit board and water solenoids
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Joliet, IL
- Parts Used:
- WR62X23154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice maker- wouldn't release cubes only crushed ice.
Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Spring, TX
- Parts Used:
- WR62X23154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator was only dispensing crush ice and not cubes
Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jimmy from saluda, SC
- Parts Used:
- WR17X2740
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
would not dispence ice
remove ice bucket and replace broken augar
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DERICE from FARMINGTON, IL
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rust Flakes In Ice
Removed ice buscket from freezer, removed 4 screws holding front cover on, set aside old ice bucket, set new ice bucket in place and reinstalled screws, putback in freezer, done. Maybee ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Colorado Springs, CO
- Parts Used:
- WR71X1936
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing a shelf in freezer
I saved about $15.00 by ordering the part on line. It came in about a week and was a super easy process. Since it was just missing there really wasn't anything that needed fixing. just installed it where it belonged and all was good. Great and easy experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Punta Gorda, FL
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad odor and rusty ice cubes. Auger had rusted and should have been covered by GE
Removed the old ice bucket assembly and dumped the contents. Removed four screws from the face plate and reinstalled it to the new ice bucket kit. Back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GENE from ASHEBORO, NC
- Parts Used:
- WR62X23154, WR62X26536, WR62X26536
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No cube ice. We had crushed ice.
Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilbur from Brazoria, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
old ice maker was rusty had not been using it
order new augerand ice bucked changed face plate 4 screws now have good clean ice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Corpus Christi, TX
- Parts Used:
- WR49X10183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rust in ice
Replaced auger and front helix kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GUSTAVO from CORONA, CA
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace Auger And Ice Assembly
Just replaced the auger from the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Cocoa Beach, FL
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The silver plating on the auger was coming loose, rusting and getting in the ice cubes.
All I had to do was remove four (4) screws from the old ice bucket assembly to remove the front cover and attach it with the existing screws to the new ice bucket assembly. It was a very simple repair. Thanks for the expedient delivery and the exact replacement part that I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leticia from El Paso, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Ice Bucket had rusted
It was really simple, remove 4 screws form the old cover and put it on the new bucket. Simple, Simple!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Canyon Country, CA
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My Auger was rusted, and discontinued. Had to buy complete Ice Bucket assembly.
Washed new Ice Bucket assembly with dish soap and warm water, and let dry. Removed (4) small screws holding Ice Bucket Door assemby to my original Ice Bucket assembly. Reinstalled Ice Bucket Door assembly to new Ice Bucket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Temecula, CA
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The auger in the ice bucket was rusted
Removed 4 screws from the old rusted ice bucket ( they hold the cover on) installed the cover and screws in the new ice bucket and installed the new unit in the freezer .
Was this instruction helpful to you?
Thank you for voting!