GTS22KCPCRBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- TREVOR from KENT, WA
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
broken slide drawer track
Took out shelf, unscrewed old track, screwed on new track. Only thing is not a standard flat or Phillips screw head so if you don't have a star head bit, you are out of luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Monroe, WI
- Parts Used:
- WR57X10086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench set
Water would not stop flowing.
First I unplugged the refrigerator. I removed the cardboard from the back and unhooked the inlet water line with a wrench and the water line to the ice maker, which was a quick connect. I unplugged the wire harness and removed the valve, then installed the new valve, plugged in the wire harness and hooked up the water lines. I turned on the water line and plugged in the refrigerator. The ice maker works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from West Hollywood, CA
- Parts Used:
- WR17X11970
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Center track for drawers had to be replaced
It was very tricky getting the old piece out, even though it was partially broken... I ended up snapping the old piece to remove it. Trying to install the new track with the glass shelf above was not working at all, but once I removed the glass shelf above it, the new piece went in pretty easily. With the glass shelf out, I could angle the track upward to get it into position. In retrospect, I should have removed the glass shelf from the start... it would have made removal of the old piece much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOYCE from REEDSBURG, WI
- Parts Used:
- WR50X10068
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
freezer not defrosting
Only problem we had was when we removed back wall on freezer the couls were totally iced up. After waiting for that to defrost. (3 HOURS) repair went fine. Was kind of hard to get to the part being its a side by side but happy with results
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- khampheuy from Kerrville, TX
- Parts Used:
- WR50X10068
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Frige was warm and Freezer was freezing up
I have checked the defrost thermostat:During the defrosting cycle the thermostat is still open
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Brooklyn, NY
- Parts Used:
- WR72X10072
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Guide rail cracked
My snack tray guide rail cracked and this was the easiest repair I've ever made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orlando, FL
- Parts Used:
- WR50X10068
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrig not turning off and defrosting
replaced the defrost thermostat. The "how to" video was superb. Watched it twice before beginning the job. repair went as described.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Houston, TX
- Parts Used:
- WR50X10068, WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
freezer side freezing and thawing
I followed the directions of the how-to video and completed job in less than 15 minutes and it solved the problem. It's been freezing like before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Simpsonville, SC
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch quit working
removed the inside fridge electrical panel and swapped switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernon from Harmony, NC
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
coil frosting up and refridgerator section was not cooling
took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Rodeo, CA
- Parts Used:
- WR50X10068, WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
not cold enough in the freezer compartment and cabin pressure also warmer than usual.
I called angies list to get a name of a repair person . We were having very hot weather and I did not want my freezer food to spoil. The cost was not bad for the look see $127.00 plus parts and labor added on to this. I decided to look on the internet and found your services and the video on how to replace the part that might be bad. I bought a new thermostat and also a sensor and added the control board as the refrigerator is 13 years old. I spent a total of $206.00 and did the work myself so no labor cost. I was so happy as a new refrigerator like this one would be $3100.00 plus tax. Thank You R. Polglase
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from Montebello, CA
- Parts Used:
- WR72X10073
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken slide pan lh
pull out the slide pan lh and replace for the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jamestown, ND
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Slide track on right side of chill tray, where it was held together, on the metal frame, the screw cracked the plastic.
Went to Sears, where I bought the Fridge, they could not locate the part I needed, so I went on line, and found partselect.com, entered the proper information, found the part I needed fast, ordered the part, received it in two days time, I already had the old part off, so it took less than ten minutes to replace it with the new part, works great, the people at partselect.com were great, an if needed, I will gladly order from them again.
Was this instruction helpful to you?
Thank you for voting!