RSG20IBPAFWW General Electric Refrigerator - Instructions

All the rest of everyone's post are all what I did. The only other thing I recommend is to put the back panel over the evaporator coils when your done. I replaced defrost thermostat, and heater. Once I initially completed it it kept icing over more than usual. You have to put the back panel back on so airflow goes over the coils.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Removed the interior shelves and set screw which holds the light cover in place. Next I removed the four screws that hold the back panel in place. Located the defrost thermostat and removed it from the aluminum tubing by unclipping it, just as it was illustrated in the repair video. Cut the wires and stripped the ends and then connected them to the ends of the new defrost thermostat. Connected them together with an 16-14 gauge crimp style end cap. Taped the entry point into the end cap to reduce moisture penetration. Reassembled the back panel, light cover and shelves.

I disconnected power. then removed all the shelving, then the cover plate at bottom back. taking the four screws off that held the next piece for the ice maker dispenser and then the cover for the fan and motor. replacing the blue grommets first then reinstalling fan with white set collar, re-securing to bracket and replacing all parts. luckily everything was a nice fit and that made the repairs easy adn fast.

Replaced top sensor in ref. and top sensor in freezer as well as defrost thermostat - works as advertised - easy fix, saved a bundle thanks to this site! Parts ordered and shipped quickly and without complications!

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

Removed the panel on the back wall inside the freezer side. To do this I unplugged the appliance, removed the racks, drawer, bulb and two screws holding the panel in place. The defrost cycle was not working so ice buildup on the coil was to the point of blocking air flow to the refrigerator side. I used a hair dryer set on high and stuffed two towels at the base of the coil to collect the melting frost and ice. Once the coil was clear of frost and ice I took the defrost timer off by sliding the clip off the tube, cut the wires and stripped the ends so I could use wire nuts to make the new connections . Placed the new defrost timer in the clip and reattached in the same location the old one was removed from. The sensor was replaced by doing the same steps. I replaced the panel after all the wire nuts were secured and the wires were tucked away where they would not interfere with the fan. Replaced the bulb, drawer, racks and food and plugged The refrigerator back in. 20 minutes from beginning to end.

I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!

We used partselect troubleshooting appilication to figure out what was most likely causing the problem and what part would fix it. The suggested part was the freezer's defrost thermostat and the probability that this would fix it was 52%! The diagnosis made sense because when we emptied the freezer to see the part, the coils were frozen solid with a thick layer of ice. We thawed the ice and the refrigerator worked fine for a day and a half at which point the ice was back and the refrigerator was warm again. We ordered the part. It came in 2 days. We snipped two wires and removed the old part, twisted the wires of the new one in place, taped it up and it worked! Fast, easy, cheep! $8 For the part, about the same for shipping and no $70 service call. Selectparts is bookmarked for "house repair"!

Remove the shelves then remove the back by removing the two screws at the top of the panel. Locate the temperature sensor on top of the coil. Cut the wires and replace with the new one. Use wire nuts and electrical tape to reconnect the wires.

I watched the videos before I received my parts. I thawed the freezer out, removed the panel in the back. Cut the wires to the defrost thermostat and spliced the new one on with wire nuts and tape. Then I did the same for the temp. sensor. Put it all back together. Now the freezer isn't running all the time. I set the temperatures back to normal and it seams to be fine.

changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.

replace sensor in refriger.

followed part select video instructions