38489KBSBRSS General Electric Refrigerator - Instructions

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Removed shelf by pushing to left and lifting up on RH end. Removed screws in plastic cooling tower and slid tower up. Pulled back wall of freezer compartment out, RH side first. Removed two screws from fan bracket, unplugged fan wiring harness by compressing connector spring clips and pulling joint apart. Pulled fan blade off (note location of blade on shaft for reinstall alignment purposes), removed both green grommets.Then just reinstalled new items.My philosphy on repairs of this nature is to replace all related parts that could be contributing to problem. The parts are cheap compared to the aggravation and inconvenience of doing the repair several times until you fix the problem. You don't need to purchase the compression ring if you buy the fan blade as it has one already installed on it. Problem solved, though now that the noise is gone am hearing fainter similar noises from lower fan. Should I be surprised, both fans are of similar design.

The part i received fit perfect, i just removed the old part and put the new part in with the screw driver.Really easy

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

First I had to go to the hardware store to buy a star bit to remove the old screws ($1.09). I attached it to my quarter-inch drill and used it to remove the old screws. I then used those same screws to attach the new slide. Once I had the star bit, it was little more than a five-minute task.

I didn't call for repair iwas just order 2 pcs it's coming early morning in the next day I was happy 1hundred% I will recommend this company

Removed glass shelf, cleaned and set aside. 2 screws attach the old bracket, one on front, one in rear. Removing front screw requires popping off cover on front of shelf. (gently) Scrub off accumulated gunk. Install new bracket reusing same screws. Place shelf in fridge, making sure bin divider is attached to shelf with open end to front so that bins can slide into place. Slide glass shelf top back in place, do this gently, does NOT require force. Pop front shelf cover back on. Gently slide in bins. Done.

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

Unplugged fridge and removed back panel inside freezer compartment . Unclipped defrost thermostat and snipped off with wire cutters . Installed new defrost thermostat with wire nuts , clipped back on , re-installed back panel , turned on fridge and within a couple hours food compartment began cooling down . Thermostat looks like a small metal can clipped onto the heating coils with 2 wires attached . Also noticed excess ice build up on coils melted and drained into pan under fridge once unit started working .

I mistakenly ordered the incorrect shelf width when trying to figure out what I needed from a similar model. I called to get assistance and the correct part was found right away. If you think there is something in question on the part you are ordering it is worth calling. The agent was very knowledgible was able to utilze additional info she had to find what I needed the first time. The return on the incorrect part went very well also.

Thanks for my new freezer compartment shelf!!

The original design is poor. The evaporator fan is mounted in an upright position just below the ice-maker. A plastic grate mounts over the fan assembly to allow for air circulation. Unfortunately, random chips of ice from the ice maker can fall into the fan, causing the fan to shear its blades. Replacement of the fan blade is relatively simple (accept for having to completely unload the freezer and remove all back covers, the ice-maker auger motor assembly, and the metal evaporator cover). In order to mimimze this from reoccuring, I installed a 1/4'' mesh metal screen over the exhaust ports on the cover. Thus far, this has worked well to keep ice chips out of the evaporator fan.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

First, remove the cardboard cover on the back, lower portion of the refrigerator.

Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)

Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the blade shaft toward the motor (away from the fan blades) to loosen.

Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.

Reverse the above steps to attach the new blade.