TFT22JABBAA General Electric Refrigerator - Instructions

Used (2) 2 x 4's as block and lever to raise door removed 2 screws and removed door used same socket to remove and replace door side of replacement part. replaced door. This is the second time I have replaced this part on frig. side. Very easy replacement.

I pulled all the items out of door, removed door top hinge cover, lifted the door off the hinge and removed the bottom hinge and closing cams and replaced them and re hung the door, just about that fast.

PS
Thanks for the parts

replace broken hinge.

Being as the part is plastic it has a limited life span. But the repair is very easy and anyone can do it. I just proped the door with 2x6's and 1x2's and bolted it in. If you get confused just look at the freezer side to see how it goes, they are the same. It's four bolts and some shims that need to go in the same locations. I'm real happy that there is an online location to get these parts as there is not anywhere to get them where I live.

I am a widow, 70 year old. Ordered parts. They came very fast. It took less than Fifteen minutes to remove door and take off broken parts and put the new ones on. I am glad I have two doors on the fridge so I was able to lift it up.

Emptied contents from the door. Removed top hinge cover (one screw) and top hinge (two bolts.) Lifted door off and replaced broken cam riser on bottom hinge. Put door back on.

Removed the upper hinge assembly. Removed the door. Removed the kick plate. Removed the old hinge assembly and installed the new one.Replaced the other broken cam on the door bottom. Then,reinstalled door to fridge and reinstalled the top hinge. PS/cleaned and lubed both upper and lower hinges.

Emptied door shelves and removed top pivot hinge bracket. lifted door of lower pivot and set aside.

Removed vent-toe base and replaced hinge 'L' bracket and cam.
Removed two bolts from bottom of door and inserted new plastic cam.
Set door back on lower pin and re-attached top hinge bracket while aligning door.

Replaced articles back in door and watched it as it it self closed. Total time, less than 15 minutes excluding cleaning of equipment while dis-assembled.

Part Number: PS290199

1. Empty the door shelves.
2. Leave the door closed.
3. Remove the grill directly beneath the doors.
a. It snaps in. Pull simultaneously on the outside edge and the bottom about 2 inches in from the outside edge.
4. Using two people. One holding up on the bottom of the door. The other removes the two screws that hold the hinge to the refrigerator.
5. Open the door slowly and let it down slowly to pull the door away from the top hinge.
6. Replace the new hinge half on the bottom of the door. Insert the other half of the hinge into the hole of the door to keep the other half lined up while tightening the screws.
7. Apply a small amount of lithium grease to the contact surfaces of the new hinge.
8. Using two people. One person is to hold the door. Best if he/she holds it from the bottom. The second person lines up the top while pushing up on the door to insert to the top hinge.
9. Insert the other half of the new hinge into the bottom of the door.
10. Line up the holes and insert the two screws that hold the bottom hinge to the refrigerator.
11. Reinstall the grill.

I was by myself so I took the entire Fridge door off. Took off the old hinge assembly and installed the new hinge assembly. The process took about 10 minutes and worked like a charm. Door closes like it did 15 years ago.

First, I loosened the top hindge bolts about halfway. Then, I took the bolts out ofthe door and then took the door off. Next I took the bottom hindge off and put the new part on. Then, reassembled the door in reverse. However, I didn't tighten the hindges until I made sure to align the door to close properly.

The magnetic door strip will hold the door in place if the door shelves are unloaded.I removed the bottom hinge with the socket set and installed the new hinge.

Remoed bottom hinge and replaced broken cam riser. Replaced Bottom hinge.

Removed two screws from the top hinge, two from the bottom - replace and put back together. It took longer to remove the food from the door than it did to replace it. THANKS

Part no. Ps290199 received matched part no. Ordered, which I obtained from your web site, however, part did not exactly match oem part. It was necessary to drill a new top hole in each of the hinges. New hole center was drilled 1/2" off (lower) then hole in supplied part. Jpb could have been accomplished easily by the avg. Homeowner, but the drilling required a little more skill & possible some tools that an average homeowner does not possess. Otherwise job was relatively easy and satisfactorily completed.