Models > ZISP420DKBSS > Instructions

ZISP420DKBSS (2016) General Electric Refrigerator - Instructions

Jump to:

All Instructions for the ZISP420DKBSS

Customer:: Tim from SANTA FE, NM
Parts Used:: WR17X11653, WR17X10706, WR02X10585
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Frost in upper portion of freezer

Removed escutcheon, removed control panel, remover and replaced flapper, spring and crank. Followed the instruction exactly. Although I hope this fixes the frosting problem, I did not see anything wrong with the parts I removed. I hope this fixes the problem,

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Justin M from Cypress, TX
Parts Used:: MWFP, WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Ice door gasket warped would not seal

Pop off the control board for the ice selector/water. Remove power / signal connections. remove four phillips screws, Remove plastic hopper. Pop off Ice door gasket, pop in new one and put back together. If you fridge was sounding like it was speeding up and slowing down, this will correct this problem as well.

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: JAMES from MORENO VALLEY, CA
Parts Used:: MWFP
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Water dispensed at a trickle

I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: NICK from COCOA bEACH, FL
Parts Used:: WR62X10055
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Ice dispenser door will not shut completely

I removed the door cover plate and disconnected the circuit board, then four screws. The part was corroded in place. Upon removing three screws and cleaning the surface, the new part was an exact fit, replaced it and everything works like new.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: jeff from stillwater, OK
Parts Used:: WR62X10055
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

solenoid quit working

repair was easy, just removed control panel and removed screws from solenoid, switched out with new, was done in minutes

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Richard from Sandy Hook, CT
Parts Used:: WR62X10055
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Ice chute wouldn't open or shut correctly - rusted solenoid

Replaced rusted solenoid.

Popped front button panel off from the bottom using flat head screwdriver; Removed 4 screws holding electronics board and disconnected wires. Unscrewed 3 phillips head screws on old solenoid and replaced with new part. Reconnected wires to board, screwed back in, and pushed panel back into to place.

Thumbs up to PartSelect - fast, straightforward service and fast delivery.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: William from W Berlin, NJ
Parts Used:: WR62X10055
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Ice forming around shoot. Flapper door not shutting letting warm air in.

I followed they instructions from the other "do it your selfers" but only replaced the solenoid. This was the cause. Rust was keeping solenoid plunger from moving and this held the flapper door open. Very easy to repair!

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Joanne from Fort Smith, AR
Parts Used:: MWFP
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Auto water stopped working, found that filter needed replacement

Unscrewed old cartridge, ordered new cartridge, installed new cartridge by following very simple instructions. Took only one day for part to arrive from PartSelect although I paid for cheapest shipping, which was "ground." I was amazed!

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Roger from CAMARILLO, CA
Parts Used:: WR17X22070
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Leaking around filter bypass plug

Took old one out with my fingers. Put new one in with my fingers.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Thomas from TYLER, TX
Parts Used:: WR62X10055
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Your video was wrong. Your step was to remove exterior frame on ice/water outlet. No need to remove.Wasted too much time trying to remove.

Remove control panel.
Remove four screw in control panel bracket.
Remove to bottom screws at bottom of solinid loose top screw.
Replace all screws.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: david from LANSING, NC
Parts Used:: WR62X10055
Difficulty Level:: Very Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

broken Ice maker dispenser

with a philips screw driver and that's all it was that easy

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: paul from PETALUMA, CA
Parts Used:: MWFP, WR60X10185
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Screw drivers

noise from freezer.(WhOOOO-oooooh, WHOOO-oooooh,......) annoying with doors closed, worse with freezer door open.

Watched some videos on youtube after typing in : refrigerator noise, and my model # (in search bar.) Found a video after determining my problem of a gentleman from partselect replacing the evaporator motor. Pretty simple job from video so I went for it ordered parts from them( I fixed the inlet valve on my dishwasher bfore with partselect before). I would call the job easier than it looks. But you need common sense and simple tools and some experience with nuts and bolts and wires. There is one bolt tucked up high under ice maker you may need a right angle nut driver or 1/4 right angle ratchet.(video pointed out). Thanks for video and quality GE parts. I now have a quiet kitchen and great room, with just a low db constant white noise like new.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: jeffrey from MAINEVILLE, OH
Parts Used:: WR62X10055
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

ice maker door wouldn't close

just watch video simple

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: ERIC from THE VILLAGES, FL
Parts Used:: WR62X10055
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Flapper Door stuck open

The only tricky part was removing the front panel. Releasing the latches required considerable force. The best tool I found was a "jack knife" type Allen wrench set, using the medium size wrench, which fit into the release hole and upward pressure did the trick. The rest of the job was very easy.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Philip from S BURLINGTON, VT
Parts Used:: WR17X11653
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Remove front cover

Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together

1 person found this instruction helpful.

Was this instruction helpful to you?

All Instructions for the ZISP420DKBSS