ZIR240NPKAII (2017) General Electric Refrigerator - Instructions

had to remove ice maker and several panels to get to the fan. wires for fan encapsulated so had to cut old and new wires then solder them together while working inside the small freezer area. not too bad all in all took about an hour to get it done. no more wind thru the trees noise and is working fine

Unplugged the freezer. Then I gained access to the fan: remove the top freezer rack, remove the ice tray, remove the air flow manifold(needed to unscrew some screws), remove the manifold over the fan and cooling element. I unscrewed the fan mounting bracket. The fan motor's wires are plumbed through some plastic that i would have had to remove, so I decided instead to cut the wires and splice in the new fan motor. Then I put everything back together - the new motor works fine and doesn't make the whining noise.

Took cover off, pushed blade on, and replaced cover

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

1) remove the ice bucket. 2) remove light cover and bulb. 3) remove back panel with 2 screws. 4) remove fan shield. 5) unlug 2 elec connections. 6) remove fan housing. 7) extract wiring grommet and use exacto knife to slice thru grommet along the length of it to release wires. don't cut light wires. 8) cut up old fan/light electrical plug to free wire nubs for light. 9) install nubs in new fan plug. 10) remove old fan motor, pull blades. 11) install blades on new fan moter and install fan into housing. 11) reinstall

Snap filter into place while holding the filter slightly away from the refrig. When filter snaps into place, push it towards refrig into place.

Since the mechanisms were in the freezer icemaker area, we deduced it was the fan motor. Ordered that from your store and it was delivered to our door in two days. Great service.

The part was replaced and our refrigerator has been quiet for the first time since we moved in almost four years ago and the refrigerator was new.

Removed food from Freezer, Unplugged refrigerator. Removed light bulb cover and ligt bulb. Unplugged and removed Ice maker and motor. Removed air duct cover from motor. Unplugged and removed evaporator housing and fan. Pulled fan blade off. Unscrewed brackets from fan motor, removed dust cap from top of motor and grommet from bottom. New motor came with 6 pin connector and four pins for evaporator fan motor. Cut the harness grommet to separate the light bulb wiring from the evaporator motor's. Pushed the the old light bulb pins (red and orange) from old connector and push them in to the new fan motor connector. Reversed the process and no more noise

Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I ordered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.

Watched a youtube on capacitors- though on a motor with a pulley, the symptoms were the same, motor running and pulley not turning-bad capacitor. Took a chance for a 17+ dollar part vs a new compressor. It worked.

We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.

Googled the model number of refrigerator with symptoms of "refrigerator wont run". Parts select web site appeared on my screen, opened Parts Select website, Partselect said probable cause of my frige symptom was that the run capacitor usually burns out 51% of the time. They were correct with the diagnosis 100%. I ordered the run capacitor for $23.00, installed it in 10 minutes, refrigerator runs good as new. Thank you for saving me cost of service call. I probably saved $200 or more. I will use Partselect again with my next problem. THANK YOU,

Easy. Followed the video instrucations. the part was right there next to the compressor.

I decided to replace motor and fan, having previously altered/trimmed the fan which stopped the howling but caused a vibration. Unplug from mains. Clear out two top shelves in freezer. Remove light cover. Remove two screws(1/4 driver)at top of steel panel in rear of compartment and let it drop. Remove two screws above light. Pry up section above light/fan housing to access two screws retaining the light/fan assembly, loosen screws sufficiently so that assembly can be lifted and removed. Disconnect wiring plug by pinching in the sides of the plug and pulling out. Pull fan off motor shaft. Remove two screws clamping motor. Cut cable tie and molded wiring grommet to free wiring. The existing light wires can be removed from the old plug by carefully cutting around the old plug to free the pins and then pushing the pins into the new plug. Reverse procedure to assemble.

Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.