TBT18NABHRWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- denis from freedom, NH
- Parts Used:
- WR60X203
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
was not defrosting
first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boyd from Blaine, WA
- Parts Used:
- WR09X20002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Could not adjust temperature
Replaced temp controller
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mackenzie from Williston, ND
- Parts Used:
- WR09X20002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Compressor would randomly not turn on. Fridge too warm sometimes.
Replace temperature control. That fixed it. Also, removed plastic bag obstructing air vent in freezer which added performance. Fridge works good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- victoria from forest park, IL
- Parts Used:
- WR71X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The part that holds the items in the door was bent.
I removed the brackets with the metal strip attached, from the door. I took a screwdriver and pressed down on the parts holding the strip to the brackets . I attached the new strip to the brackets and then attached the whole thing to the door.
Really easy to do.
Really easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose A from WEST PALM BCH, FL
- Parts Used:
- WR09X20002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Was getting too cold
Was only two screws after that carefully took the part away unplugging the wires at the same time was plugging in to the new part and was done after 5 or 7 min
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jamie from san clemente, CA
- Parts Used:
- WR71X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door shelf bar was bent and no longer holding in items
we ordered new bar, cut to fit with instructions, and voila! easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rochelle from Culver City, CA
- Parts Used:
- WR71X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A cracked bar in the refrigerator door
I snapped out the old cracked bar and snapped in the new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Sarasota, FL
- Parts Used:
- WR12X10108, WR12X10107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The handles on my GE fridge had yellowed over 12 years use.
Just took the old ones off, the new ones went right on. Took less than 10 minutes. It`s nice to order parts and get the right ones on the first try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boris from East Lansing, MI
- Parts Used:
- WR12X10108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no problem
easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Owls Head, ME
- Parts Used:
- WR32X10500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken crisper drawer support
quick and simple--removed the old one and slid new part in on same support pins.I had the new part via UPS LESS THAN 24 HRS.FROM THE TIME I PLACED THE ORDER! THANKS, SOMEONE IS REALLY ON THE BALL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Danville, CA
- Parts Used:
- WR12X10107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The beyond cheap GE handle broke on our rental unit GE refrigerator after less than six months
The new handle just took three screws matching our model refrigerator perfectly--and it is much sturdier than the original. We originally went to the GE site and they wanted $70 +shipping for the same handle. Our landlord only paid $500 for this fridge six months ago--brand new! For a total of just under $17 we got a new handle in perfect condition--delivered quickly to our door. It was exactly as described and fit our model perfectly. We couldn't be happier and will tell all of our friends about this wonderful site. Thank you!!
Was this instruction helpful to you?
Thank you for voting!