ZICS360NRGLH General Electric Refrigerator - Instructions

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Moved stuff out of my way on the top shelf, reached in and turned old filter to remove. Filled new filter with water, lined up and turned to lock in place. Whew, never thought I would get that job done. :-)

Remove the rear cover, shut off the water, removed the hose, unplugged the electrical connector, removed the screw holding the valve on. Removed the plastic tube going into the freezer and reversed the steps

Tried replacing water valve since no water in ice cube tray. Exact part not available due to age of refrigerator, but I got the equivalent replacement part for $18. Mounting holes different, but I made it work. Also one connect on new one slip connect whereas both compression fittings on old valve. I put it back together and icemaker now works great.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.

Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.

Removed old valve easily. New WR57XI0033 valve is designed to mount on lower left, but on mine it has to mount on lower right. Had to drill two 1/32 holes in lower rail to mount the new valve.

Watched some videos on youtube after typing in : refrigerator noise, and my model # (in search bar.) Found a video after determining my problem of a gentleman from partselect replacing the evaporator motor. Pretty simple job from video so I went for it ordered parts from them( I fixed the inlet valve on my dishwasher bfore with partselect before). I would call the job easier than it looks. But you need common sense and simple tools and some experience with nuts and bolts and wires. There is one bolt tucked up high under ice maker you may need a right angle nut driver or 1/4 right angle ratchet.(video pointed out). Thanks for video and quality GE parts. I now have a quiet kitchen and great room, with just a low db constant white noise like new.

1.Google troubleshooting for this issue. Determine the inverter card was bad. Installed new card and correct jumper harness per instructions. Total time to troubleshoot, remove & replace was about 30_45 min. Pretty simple

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

removed back cover--disconnect water supply-- removed screw holding vave and unplugged the
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.

Replaced Temperature Sensor and now it is getting cold.

Took the old filter out and put the new one in.
Easy Breezy!!

My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!