Models > GSE25GYPGCFS > Instructions

GSE25GYPGCFS General Electric Refrigerator - Instructions

Jump to:

All Instructions for the GSE25GYPGCFS
91 - 105 of 164
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mike from Rowlett, TX
Parts Used:
WR29X43993
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Bucket assembly broke
Slid right in; identical to original part. Took 5 seconds to install.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from Dubuque, IA
Parts Used:
WR17X20449
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Replacement of paddle and spring
Watched the video from you
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Orill from PITTSBURG, CA
Parts Used:
WR55X40445
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Refrigerator freezer and cooling sections both about 20 degrees too warm.
I called out a repairman who used a laptop to troubleshoot. He charged me $119 just to come out. He told me that the control board wasn't telling the evaporator to periodically defrost and I noticed that it was encased in ice. Then, he gave me an estimate of $400 to replace the board. Breaking down the estimate, that would be $200 for labor, about 30 minutes, and another $200 for the board, however, he didn't have a replacement board in stock. Knowing that I could replace the board myself, I was happy to order the board from PartSelect and save on the $200 labor charge.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from BERLIN CENTER, OH
Parts Used:
WR71X38317
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Door was broken
My wife did it in less than five minutes
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Trevor from ALAMOGORDO, NM
Parts Used:
WR60X10307
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Motor stopped due to corrosion
Uncovering the motor is the most difficult part. Installation is stupid-easy. Put all of the coverings back on in reverse order to the way they were removed. I don't think the ice maker has to come out but we weren't using it so it came out first.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from NEW YORK, NY
Parts Used:
WR02X10540
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
noisy refrigerator
I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
QUOC-LOC from LYNN HAVEN, FL
Parts Used:
WR55X24064
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The control board generated clicking noise. Temperature display wrong values.
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
pat from ERIE, CO
Parts Used:
WR23X31507
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Interior light door switch broken when jar fell off shelve and hit switch
Very easy with small screw driver . Carefully pry broken switch out pull off two connectors install new switch connect as before . Unplug refer 1st . Works great . Refrigerator will not work with bad switch
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Evelyn from ALTON, MO
Parts Used:
WR23X31507
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Light switch wouldn't turn on inside light
I used the pliers to hold switch while I got screwdriver under the switch then pulled out. I THEN unplugged old one and plugged in New one and put it back in place.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ken from Acton, CA
Parts Used:
WR29X43993
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken bucket assembly
This is about the easiest repair you can make. Simply pull out the old auger/bucket assembly and reinsert the new one and your done!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rose from Dorr, MI
Parts Used:
WR60X30922
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Broke the fan blade when replacing the Evaporator motor
Took cover off, pushed blade on, and replaced cover
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sharri from Charlotte, NC
Parts Used:
WR23X31507
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Child Broke Light Switch Inside Refrigerator
Pulled out broken switch with flat head screwdriver and replaced with replacement part purchased from partselect. Easily plugged in new part and replaced.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Waterford, MI
Parts Used:
WR23X31507
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light Switch Malfunction
Really easy
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lourdes from Miami, FL
Parts Used:
WR71X38317
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The egg door fell and cracked! ughh
No tools just opened the box and popped the new part into place...that easy!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
aaron from reynoldsburg, OH
Parts Used:
WR23X31507
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Hing door brine off
Poped whole switch out with flat head screw driver. Removed wires with needle nose players and held the wires so they wouldn't get pulled back inside fridge shell. Attached wires to new part like a plug. Lights ccame back put new switch back inside wall. Shut door
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GSE25GYPGCFS
91 - 105 of 164