XSS25GGPFCWW General Electric Refrigerator - Instructions

I reached into the refrigerator top shelf for the bottle of milk and my arm caught on the Dairy Door and pulled it from the door and it fell to the floor and shattered. Thanks to you I was able to order another. After couple of weeks, I asked my wife, Rita if we received the Dairy Door. She said, "Oh yes. I installed it already." Boy was I surprised. Rita doesn't do installations!!!! Thank you, Thank you, Thank you.

Watched a youtube on capacitors- though on a motor with a pulley, the symptoms were the same, motor running and pulley not turning-bad capacitor. Took a chance for a 17+ dollar part vs a new compressor. It worked.

We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.

Ordered the part and within three working days the part was delivered. It took two minutes to pry off the broken part and one minute to snap in the new one.

just put it in

Used screw driver to lightly remove the old switch. Disconnected the 2 electrical leads to the old switch, then I connected those leads to the new switch. The light immediately came back on and I placed the switch into its housing hole and popped it in place. It works perfectly now. My wife said "let there be light"! Very easy installation. Thanks.

pulled out the old shelf/drawer frame and replaced with new one. Easy fix.

i followed all the other submited solutions. really easy. popped out the broken light switch with thin tip screwdriver. careful not to let wires slip into compartment. then attached wires as i pulled them off broken switch. then carefully pop the new switch back in the slot. when i was younger i worked for an appliance repair company. i felt confident in this repair.

Remove the ice bucket assy. Slider attaches with two screws in the left hand side and one thru the icemaker that attaches it to the track. Just about as easy as it gets.

its not the repair we live in the last town of n h and I broke the dairy door of my refrigerator in millions of peace I found your site in the middle of the afternoon order the parts and the next morning the part was there we pay for over night deleverie and it always come couple day after never never see a company like yours thank you for your site I tell every bodies about you

No tools needed - simply a middle hydrator drawer replacement. Pulled out old (broken) drawer and slid in new replacement.

about an hour to figure out what was causing the vibration and noise and about an hour to put it back together and 5 min. to order a new fan blade thank you.It started making noise during thanksgiving dinner so we toke it apart after dinner and I cut the other 2 blade to match the broken one so to cut down on the noise and vibration semi put it back together and 7 days later the part arrived.

Used a small screw driver to remove the damaged switch. Carefully unhooked the two wires and hooked the wires to the new switch. Pushed the new switch into place. Be careful that the wires do not pull back into the refrigerator wall. Took about 15 minutes. Works like New. Easy fix.

Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I ordered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.

I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.