XSS23GGPECBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carla from Sublette, IL
- Parts Used:
- WR32X32346
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Bottom refrigerator drawer cracked tracks
Pull out old drawer and replace with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from DETROIT, MI
- Parts Used:
- WR71X38317
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dairy door was broken.
Received replacement door, aligned it then pressed it into place.
Gee, thanks.
Gee, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from SEMINOLE, FL
- Parts Used:
- WR32X32346
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Someone broke the bottom refrigerator crisper drawer
Slide the old drawer out and insert new drawer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FORT BRAGG, CA
- Parts Used:
- WR71X38317
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked dairy door
Clear plastic dairy door snaps into placed at the hinge . No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dolores from POULSBO, WA
- Parts Used:
- WR32X10155
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The cover pan glass slipped out and shattered into the kitchen sink.
The glass just slipped back into the spot perfectly. Thank you so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from OROVILLE, CA
- Parts Used:
- WR71X38317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced broken dairy door
Took 2 seconds to replace door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from MESA, AZ
- Parts Used:
- WR71X38317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Part for area of butter etc got broken
aligned and pushed on by hand
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzette from Northridge, CA
- Parts Used:
- WR62X39469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The ice maker wouldn’t switch from crushed ice to whole cube.
I looked up a YouTube video that showed the step-by-step how to replace the crusher solenoid in my GE side-by-side refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from KNOXVILLE, TN
- Parts Used:
- WR60X30922
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice built up around evaporator fan blades and blades chipped and broke. Refrigerator was making loud vibrating noises.
Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gwendoline from VERO BEACH, FL
- Parts Used:
- WR72X10170
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Broken rail right side of the freezer compartment that holds the ice container
As a female DIY, I found the job easy enough and the only difficulty was the correct tool to remove the two screws. It is NOT a "usual type" screw like a Philips or flat blade.. I believe the correct name is a Torx screwdriver, so check out the screw first before starting the job. There are two screws holding the runner, one at the front and another at the back. Mine was at the back where the rail had broken.
When you have the correct screwdriver then you are ready to begin.
1. Remove the ice container.
2. Remove the top shelf that sits above the ice container., it slides out.
3. Turn off the electric switch on the back upper left corner which stops the ice cubes being formed. (Just like a regular light switch)
4. The broken rail is exposed, and the two screws are visible one at the front that in my case was okay, and the other at the back holding the other screw was where the plastic rail had broken.
5. You will need to get your head right inside the freezer to be able to visualize where the screw is fitted in but it was easy to remove once you can see it, and then unscrew the front one.
6. I learned from experience of trying to screw in the back one first that it is a fiddling job and needs small hands, otherwise you might lose the screw, been there and did that! So I chose to screw the front one in sort of lose which was much easier for lining up the hole and the back screw, then I tightened them both up sufficiently secure not to break the plastic.
7. Before you hasten to whip all the things back in the fridge, TURN on the ice maker switch - top left that was previously turned off, otherwise you will have to remove the top shelf again because it hides that switch. Once done put your shelf back and then the ice drawer and all is good to go.
8. Mine is working great now, just need to be careful if you lift the drawer in and out to remember it is only plastic.
The job was easy and the only exception would be finding the correct screw driver first before starting the job, otherwise just a few minutes work to change the rail.
When you have the correct screwdriver then you are ready to begin.
1. Remove the ice container.
2. Remove the top shelf that sits above the ice container., it slides out.
3. Turn off the electric switch on the back upper left corner which stops the ice cubes being formed. (Just like a regular light switch)
4. The broken rail is exposed, and the two screws are visible one at the front that in my case was okay, and the other at the back holding the other screw was where the plastic rail had broken.
5. You will need to get your head right inside the freezer to be able to visualize where the screw is fitted in but it was easy to remove once you can see it, and then unscrew the front one.
6. I learned from experience of trying to screw in the back one first that it is a fiddling job and needs small hands, otherwise you might lose the screw, been there and did that! So I chose to screw the front one in sort of lose which was much easier for lining up the hole and the back screw, then I tightened them both up sufficiently secure not to break the plastic.
7. Before you hasten to whip all the things back in the fridge, TURN on the ice maker switch - top left that was previously turned off, otherwise you will have to remove the top shelf again because it hides that switch. Once done put your shelf back and then the ice drawer and all is good to go.
8. Mine is working great now, just need to be careful if you lift the drawer in and out to remember it is only plastic.
The job was easy and the only exception would be finding the correct screw driver first before starting the job, otherwise just a few minutes work to change the rail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from GROVELAND, FL
- Parts Used:
- WR02X10821
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Slide control was broken
Simply slide new control slide through slot from front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACOB from COLLEGEVILLE, PA
- Parts Used:
- WR62X23154
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Only crushed ice. No cubed.
Found a step by step video on YouTube made replacement very easy. Cubed ice is back. Time for a cocktail to celebrate!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pat from ERIE, CO
- Parts Used:
- WR23X31507
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior light door switch broken when jar fell off shelve and hit switch
Very easy with small screw driver . Carefully pry broken switch out pull off two connectors install new switch connect as before . Unplug refer 1st . Works great . Refrigerator will not work with bad switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evelyn from ALTON, MO
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light switch wouldn't turn on inside light
I used the pliers to hold switch while I got screwdriver under the switch then pulled out. I THEN unplugged old one and plugged in New one and put it back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clayton from TUCSON, AZ
- Parts Used:
- WR62X23154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice crusher did not work, Ice would plug in tub chute on discharge end.
Pulled ice tub, removed auger rotation motor and solenoid housing, removed solenoid and replaced with new one and reinstalled. Checked solenoid was working by holding freezer door open and closing switch to door an activating ice switch-- solenoid picked up. Put ice tub with auger back into freezer.
Was this instruction helpful to you?
Thank you for voting!