XSS25GGPGCWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vernon from NEW PRT RCHY, FL
- Parts Used:
- WR32X32346
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My bottom drawer in my GE refrigerator was broken.
Pulled out broken drawer and inserted new drawer...just that simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Littleton, CO
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Light Would Not Go On
Knew the switch was bad. Researched on the internet how to fix. Used a steak knife to pop the old one out, changed the contacts to the new switch and popped it back in. It took longer to open the box than it did to replace the switch. And the part arrived 2 days after I ordered it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Rowlett, TX
- Parts Used:
- WR29X43993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bucket assembly broke
Slid right in; identical to original part. Took 5 seconds to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dolores from POULSBO, WA
- Parts Used:
- WR32X10155
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The cover pan glass slipped out and shattered into the kitchen sink.
The glass just slipped back into the spot perfectly. Thank you so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FORT BRAGG, CA
- Parts Used:
- WR71X38317
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked dairy door
Clear plastic dairy door snaps into placed at the hinge . No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from CINCINNATI, OH
- Parts Used:
- WR29X43993
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I’ve bucket didn’t function properly
I pulled out the old drawer and installed the new one.
Then dumped thrice from the old drawer into the new one.
Then dumped thrice from the old drawer into the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from GEORGETOWN, TX
- Parts Used:
- WR71X38317
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The existing dairy door came lose fell and brokeon tile floor.
The new part installed without problem always had great service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from PALMYRA, VA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The switch was loose ( no spring). The lights did not work.
Unplug the refrigerator. Gently pry old switch out with screw driver. Move wires to connector on new switch with needle nose pliers. Pop it back into the hole. Plug back in. Peek inside to see the lights working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from montgomery, TX
- Parts Used:
- WR29X43993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice dispenser did not dispense ice
Ordered the part on a Tuesday and received the NEXT day. Slid out the damaged part and then slid in the new part!!! Excellent Service from your company and will recommend highly!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Vacaville, CA
- Parts Used:
- WR12X10626
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken shelf face
+The shelf face has little plastic locator clips that snapped off. the shelf face just comes off with a light lift of these two clips and a slight upward pull then lift up and off. The new one slips on with the top slipping onto the top rail of shelf, then push the bottom tow clips over the bottom rail of the shelf. There you have it smooth as glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from PASCO, WA
- Parts Used:
- WR72X10233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
part broke
remove three bolts, installed the new part and was all done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from OROVILLE, CA
- Parts Used:
- WR71X38317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced broken dairy door
Took 2 seconds to replace door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from TUCSON, AZ
- Parts Used:
- WR14X10059
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
replace seal on crisper drawer
spent 10 minutes trying to clip in the seal without any success. I emptied the crisper drawer and removed it flipped it over clipped the seal. replaced the drawer. Secret is to remove the drawer from the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from ALAMOGORDO, NM
- Parts Used:
- WR60X10307
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Motor stopped due to corrosion
Uncovering the motor is the most difficult part. Installation is stupid-easy. Put all of the coverings back on in reverse order to the way they were removed. I don't think the ice maker has to come out but we weren't using it so it came out first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Orill from PITTSBURG, CA
- Parts Used:
- WR55X40445
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Refrigerator freezer and cooling sections both about 20 degrees too warm.
I called out a repairman who used a laptop to troubleshoot. He charged me $119 just to come out. He told me that the control board wasn't telling the evaporator to periodically defrost and I noticed that it was encased in ice. Then, he gave me an estimate of $400 to replace the board. Breaking down the estimate, that would be $200 for labor, about 30 minutes, and another $200 for the board, however, he didn't have a replacement board in stock. Knowing that I could replace the board myself, I was happy to order the board from PartSelect and save on the $200 labor charge.
Was this instruction helpful to you?
Thank you for voting!