ZIP360NNG General Electric Refrigerator - Instructions

I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.

Followed the instructions. Smooth as silk. This part is better than the original. There appears to be a sensor that beeps when the ice reservoir is full.

I spent 15 - 20 minutes just hunting/deciding which of several sets of parts & directions to follow. The provided directions were not bad; but none of them quite matched my GE ADORA side-by-side model. Once I came up with the actions I would need to take...I was done in 5 minutes! The kit , as I said, came with all the parts one could need (and one or two un-needed parts included for other model GE refrigerators) I am very happy with PART SELECT...altough GE doesn't rate as high with me for their declining reliability.

Removed old ice maker, then screwed in new ice maker. Only thing that was a little difficult was to hold the auger motor, while trying to unplug the clipped in plug on the old ice maker. I could have used an extra pair of hands.

I had to defrost the freezer to free the icemaker. After that the installation was plug and play with two small exceptions: 1) I had to file down the width of the left hand tine of the old stripper so that it would fit the new icemaker, and 2) the motor housing of the new icemaker was slightly wider than the old one. It fit, but just barely. But I'm back in the ice again, no dripping water, all is good.

Installing the actual ice maker was quite easy. What takes most of the time is preparing the freezer for the install. Need to remove all shelving, (and the door) to gain access to the unit. The ice maker is simple to install once access is achieved. Putting everything back together takes some time.

I watched the video and then read the instructions. Emptied and cleaned freezer compartment. Removed old unit and removed part of old unit to be used in new installation. I then installed the new unit and turned the water back on. I let the unit produce over night and through the first batch of ice away. Because of the various regrigerators this ice maker was used I had a little confusion recognizing our model, but worked through this problem useing some common sense. All around I'm very satisfied with the results.

I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel and it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

Went well. Changed the Ice Maker and then the Water Valve. All good and it is making ice.

Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.

I read the step by step instructions that came with the part. I turned two screws and disconnected the electrical harness and Removed the icemaker. Two other parts from the old icemaker were easily removed without any tools and put on the new icemaker. The new icemaker was put in the same way the old one came out. I reconnected the electrical harness and tightened the old screws. The hardest part of the whole job was reading the directions. They were easy to follow if you take the time to Just read them!

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

I watched the video from the link that was sent to me with the shipping notice. It was very easy to understand. I had no trouble at all. I'm 75 years old woman, however, and I can fix about anything. Don't be afraid to fix appliances yourself if you feel you have the knowledge.

removed the inside fridge electrical panel and swapped switches

Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.