GZS22IMNYHES General Electric Refrigerator - Instructions

Poped whole switch out with flat head screw driver. Removed wires with needle nose players and held the wires so they wouldn't get pulled back inside fridge shell. Attached wires to new part like a plug. Lights ccame back put new switch back inside wall. Shut door

The light switch was accidentally broken. I looked it up on your site and found the part. I ordered it and switched it out in a matter of minutes. It also helped having people who purchased their switches from the site explain how they repaired their switches with relative ease.

Used a 2" putty knife to lift off the old switch. Disconnected the broken switch and replaced it with the new one. Took about 1 minute.

Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.

Used a small screw driver to remove the damaged switch. Carefully unhooked the two wires and hooked the wires to the new switch. Pushed the new switch into place. Be careful that the wires do not pull back into the refrigerator wall. Took about 15 minutes. Works like New. Easy fix.

I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.

Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.

Pried out the old light switch, disconnected electrical, reconnected electrical in new switch, pushed new switch back into door.

Pried the switch on the bottom with a flathead screwdriver, twisted it and the switch came out far enough to take it out by hand. The bottom of the switch has to be raised upward a little because the connectors are on top of the switch. Changed the wires from the old switch to the new one, one at a time. Insert the new switch. Saved a repair call, and probably a more expensive switch. Less then 15 minutes.

Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.

Used screw driver to lightly remove the old switch. Disconnected the 2 electrical leads to the old switch, then I connected those leads to the new switch. The light immediately came back on and I placed the switch into its housing hole and popped it in place. It works perfectly now. My wife said "let there be light"! Very easy installation. Thanks.

and a rat recently got trapped in the house while the owner was away. The rat chewed the grill quite a bit too. The repair was accomplished using a phillips screwdriver on the two screws which attach the grille to the refrig.

frig ran to much and pump on to long noticed light switch sticking when door was opened replaced the light switch took care of the problem the switch controlles more than just the light popped out with a screwdriver careful to find the side of it that has the retainer clip on it and the direction of the switch in correct position so it goes off when you close the door flat side facing the back a 2 minute job at most

i followed all the other submited solutions. really easy. popped out the broken light switch with thin tip screwdriver. careful not to let wires slip into compartment. then attached wires as i pulled them off broken switch. then carefully pop the new switch back in the slot. when i was younger i worked for an appliance repair company. i felt confident in this repair.

Googled the model number of refrigerator with symptoms of "refrigerator wont run". Parts select web site appeared on my screen, opened Parts Select website, Partselect said probable cause of my frige symptom was that the run capacitor usually burns out 51% of the time. They were correct with the diagnosis 100%. I ordered the run capacitor for $23.00, installed it in 10 minutes, refrigerator runs good as new. Thank you for saving me cost of service call. I probably saved $200 or more. I will use Partselect again with my next problem. THANK YOU,