GSS25IMNYHES General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mike from Rowlett, TX
- Parts Used:
- WR29X43993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bucket assembly broke
Slid right in; identical to original part. Took 5 seconds to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Good Hope, GA
- Parts Used:
- WR29X43993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Ice Bucket & Auger Assembly plastic broken and cracked
Really easy, removed top lid, removed broken Ice bucket, rinsed and inspected new ice bucket for any packing or shipping materials, installed new ice bucket & Auger assembly and installed top lid. Ice dispenser works just like it was new.
Highly recommend for replacement parts. Great customer service support, OME and speedy shipping.
Highly recommend for replacement parts. Great customer service support, OME and speedy shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Medford, NY
- Parts Used:
- WR72X10234
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Right ice bucket Glide broke at the connection towards the front of the freezer
Very simple install.
Take the ice bucket and top shelf off and pull it out of the freezer. Get a nut driver for the bolt holding the auger motor onto the left side glide. Then maneuver the auger motor off the left side glide and take the 2 screws out of the right glide and replace with new glide.
Take the ice bucket and top shelf off and pull it out of the freezer. Get a nut driver for the bolt holding the auger motor onto the left side glide. Then maneuver the auger motor off the left side glide and take the 2 screws out of the right glide and replace with new glide.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from TUCSON, AZ
- Parts Used:
- WR14X10059
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
replace seal on crisper drawer
spent 10 minutes trying to clip in the seal without any success. I emptied the crisper drawer and removed it flipped it over clipped the seal. replaced the drawer. Secret is to remove the drawer from the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carla from Sublette, IL
- Parts Used:
- WR32X32346
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Bottom refrigerator drawer cracked tracks
Pull out old drawer and replace with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from BURNEY, CA
- Parts Used:
- WR02X11331
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Loud Squeal when fan was running
WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEW YORK, NY
- Parts Used:
- WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
noisy refrigerator
I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from KNOXVILLE, TN
- Parts Used:
- WR60X30922
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice built up around evaporator fan blades and blades chipped and broke. Refrigerator was making loud vibrating noises.
Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from GROVELAND, FL
- Parts Used:
- WR02X10821
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Slide control was broken
Simply slide new control slide through slot from front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- QUOC-LOC from LYNN HAVEN, FL
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The control board generated clicking noise. Temperature display wrong values.
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharri from Charlotte, NC
- Parts Used:
- WR23X31507
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Child Broke Light Switch Inside Refrigerator
Pulled out broken switch with flat head screwdriver and replaced with replacement part purchased from partselect. Easily plugged in new part and replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Acton, CA
- Parts Used:
- WR29X43993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken bucket assembly
This is about the easiest repair you can make. Simply pull out the old auger/bucket assembly and reinsert the new one and your done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from Dorr, MI
- Parts Used:
- WR60X30922
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broke the fan blade when replacing the Evaporator motor
Took cover off, pushed blade on, and replaced cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Waterford, MI
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch Malfunction
Really easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- aaron from reynoldsburg, OH
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Hing door brine off
Poped whole switch out with flat head screw driver. Removed wires with needle nose players and held the wires so they wouldn't get pulled back inside fridge shell. Attached wires to new part like a plug. Lights ccame back put new switch back inside wall. Shut door
Was this instruction helpful to you?
Thank you for voting!